Adaptive Thermostat

Turn any temperature sensor and any heater into a thermostat that actually regulates
Turn any temperature sensor and any heater into a thermostat that actually regulates

Læs mere ›

Understøttede enheder

Flow-kort

Klik på en enhed ovenfor for kun at vise relaterede Flow-kort.

Når...

Boiler
The central mode changes
i
Fires whoever made the change — a Flow or the picker. Only a real change fires it: setting the mode it already holds does nothing.
Boiler
The boiler is started
Boiler
The boiler is stopped
Thermostat
Tændt
Thermostat
Slukket
Thermostat
Måltemperaturen blev ændret
Thermostat
Temperaturen ændrede sig
Thermostat
The preset changes
i
Fires whoever made the change — a Flow, the picker, or a timed preset falling back on its own. It reports the preset you asked for, so with the Activity preset it does not fire when motion switches the level underneath; use Status for that.
Thermostat
It starts calling for heat
i
Fires when this thermostat goes from not needing heat to needing it. Useful to drive a boiler yourself instead of using the Boiler device.
Thermostat
It stops calling for heat
Thermostat
An open window is detected
i
Fires once the detection is confirmed, after the configured delay — not the instant the contact opens.
Thermostat
The window is closed again
Thermostat
The room sensor goes quiet
i
Fires when no fresh reading has arrived for too long. The thermostat stops asking for heat rather than regulating on a dead value — this is your warning that a battery is flat.
Thermostat
Preheating starts
i
Fires when a target set with « Reach a preset at a time » switches its preset ahead of time. The lead tells how many minutes early it started.

Og...

Boiler
The boiler is running
Boiler
The central mode is ...
Thermostat
Er tændt
Thermostat
The preset is ...
Thermostat
A window is detected open
Thermostat
It is calling for heat
Thermostat
Someone is home
Thermostat
A preheat is scheduled

Så...

Boiler
Set the central mode to ...
i
Applies to every thermostat that opted in, in its settings.
Thermostat
Tændt
Thermostat
Slukket
Thermostat
Tænd eller sluk
Thermostat
Indstil temperaturen °C
Thermostat
Set the preset to ...
Thermostat
Set the preset to ... for 60 minutes
i
The previous preset comes back on its own when the time is up. It survives a restart of the app.
Thermostat
Cancel the timed preset
Thermostat
Reach ... at ...
i
Starts heating early enough for the room to be at the preset's temperature at that time, from the rise speed the app measures in this room. Up to 4 targets per thermostat; a manual change in the hours before cancels it.
Thermostat
Cancel scheduled preheats
Thermostat
Set the target to ... °C
i
Switches the preset to Manual, like turning the dial by hand.
Thermostat
... the window detection
i
Keeps heating even with a window detected open. Useful for a room that is aired all day on purpose.
Thermostat
Force presence to ...
Thermostat
Set the indoor coefficient to ... and the outdoor one to ...
Advanced

Support

Har du et problem med denne app? Kontakt udvikleren her.

Hvad er nyt

Version 1.5.3 — Temperature devices whose app reports in °F are now read correctly. A sensor at 72.8 °F was taken for 72.8 °C, so the thermostat stopped heating and showed about 163 °F. The app now converts according to the unit the device declares, for sensors and for heaters that take a target temperature.

Se ændringslog

Adaptive Thermostat

Denne app kan administrere hele din Homey.

Adaptive Thermostat er ikke kompatibel med den valgte Homey.

Adaptive Thermostat bliver snart installeret på Homey.
Installer