Heimdall
Surveillance Mode changed.
Heimdall
Turn your Homey into a surveillance system
All detected motion and open/closed doors and windows on selected sensors will be seen by Heimdall. All these events will be logged and when Heimdall is in a Surveillance Mode the alarm will be triggered.
Supported Languages
🇬🇧 English
🇩🇰 Dansk
🇩🇪 Deutsch
🇪🇸 Español
🇫🇷 Français
🇮🇹 Italiano
🇳🇱 Nederlands
🇳🇴 Norsk
🇸🇪 Svenska
Supported Devices
• Any device that has motion detection, i.e. Fibaro Motion Sensor, Aeotec MultiSensor, Xiaomi Human Body Sensor etc.
• Any device that has contact detection, i.e. Fibaro Door/Window Sensor, Aeotec Recessed Door Sensor etc.
• Devices that don't have these capabilities can most likely be integrated by using a Virtual Device.
How do I get it to work?
• Add a Surveillance Mode Switch.
• Select the devices to monitor on the settings page.
• Add flows to activate and deactivate the desired Surveillance Mode.
• Add a flow with the desired actions when the alarm is triggered.
• Add a flow to deactivate the alarm.
• Add an Alarm Off Button
Please visit the Heimdall topic on the Athom Community Forum for more information, click on Visit forum >> under Community in the grey block below.
(Or copy this link and paste it in your browsers address bar: https://community.athom.com/t/134)
지원되는 디바이스
Flow 카드
위의 디바이스를 클릭하면 관련 Flow 카드만 표시됩니다.
언제...
This card is triggered when the Surveillance Mode is changed, the new Mode is available in the Surveillance Mode tag.
Heimdall
Sensor active at arming.
This card is triggered when there is a sensor in active state when the Surveillance Mode is set to Armed or Partially Armed.
Heimdall
Sensor active at Status Check.
This card is triggered when there is a sensor in active state when a Sensor Check is run.
Heimdall
The alarm is activated.
This card is triggered when the Alarm State is activated. The Zone and Reason are available in the tags.
Heimdall
The alarm is deactivated.
This card is triggered when the Alarm State is deactivated. The way the Alarm State is deactivated is available in the Source tag.
Heimdall
The alarm delay is activated.
This card is triggered when the Alarm Delay is activated. The length of the delay, Zone and Reason are available in the tags.
Heimdall
The arming delay is activated.
This card is triggered when the Arming Delay is activated. The length of the delay is available in the Duration tag.
Heimdall
The time until alarm changed
This card is triggered when the Alarm Counter changes. The seconds left are available in the Seconds until alarm tag.
Heimdall
The time until armed changed
This card is triggered when the Arming Counter changes. The seconds left are available in the Seconds until armed tag.
Heimdall
A logline was written
This card is triggered when a line is written to the log for a device that has logging enabled. The Zone, Device and State are available in the tags.
Heimdall
Sensor tripped in Alarmstate
This card is triggered when a sensor is tripped while the Alarm State is active. The Zone, Device and State are available in the tags.
Heimdall
No information received
This card is triggered when a device has not communicated with Homey for 24 Hours. All devices are checked when changing the Surveillance Mode or using the Check Last Communication Flow card. The Duration, Last communicationtime, Zone and Device are available in the tags.
Mode
홈 알람 상태가 변경되면 ...
그리고...
Heimdall
Surveillance mode is ...
Evaluates if the Surveillance Mode is a certain value.
Heimdall
Arming countdown active
Evaluates if an Arming Countdown is (not) active.
Heimdall
Alarm countdown active
Evaluates if an Alarm Countdown is (not) active.
Heimdall
Alarm state is active
Evaluates if the Alarm State is (not) active.
Heimdall
device is delayed
Evaluates if the chosen device has the delayed setting.
Heimdall
device is logged
Evaluates if the chosen device has the logged setting.
Heimdall
device is part of Full Surveillance Mode
Evaluates if the chosen device is used in the Full Surveillance Mode.
Heimdall
device is part of Partial Surveillance Mode
Evaluates if the chosen device is used in the Partial Surveillance Mode.
Mode
홈 알람 상태가 다음이면 ...
그러면...
Alarm
버튼 누르기
Heimdall
Send ... to Heimdall
The text that is sent to Heimdall will be written to Heimdalls history log.
Heimdall
Clear Heimdall history
Heimdall
Activate Alarm
Heimdall
Deactivate Alarm
Heimdall
Check Last Communication
Checks if devices that are included in a Surveillance Mode have communcicated with Homey in the last 24 hours. Make a flow with the triggercard No information received to process the results.
Heimdall
Check Status of all sensors
Checks the status of all Motion- and Door/Windows sensors. Make a flow with the triggercard Sensor active at Status Check to process the results.
Heimdall
Send ... to Timeline
Heimdall
Add Delay to device
Heimdall
Remove Delay from device
Heimdall
Add Logging to device
Heimdall
Remove Logging from device
Heimdall
Add device to Partial Surveillance Mode
Heimdall
Remove device from Partial Surveillance Mode
Heimdall
Add device to Full Surveillance Mode
Heimdall
Remove device from Full Surveillance Mode
Mode
홈 알람 상태 설정 ...
Mode
버튼 누르기
Mode
Set Surveillance Mode to ...
지원
이 앱에 문제가 있습니까? 개발자에게 문의하려면 여기를 클릭하세요..
새로운 기능
버전 2.10.17 — • Added RDIF tag to user settings • Improved error handling
Heimdall
이 앱으로 Homey 전체를 관리할 수 있습니다.
선택하신 Homey에 Heimdall이(가) 호환되지 않습니다.
Heimdall이(가) 곧 Homey에 설치됩니다.
업데이트 로그
