Nibe S-Series
Activé
Nibe Live
Local Nibe control, split into the devices you actually automate
Nibe Live talks to your Nibe heat pump directly over your local network, without going through the myUplink
cloud. Temperatures, power, energy and operating modes are all shown, you can change settings such as modes and
target temperatures, and everything is available as Flow triggers, conditions and actions.
What makes it different is that one physical pump is added as several devices — one per function, such as
heating, hot water, cooling and pool — each with its own values and its own energy meter, so you can see how
much energy goes to hot water versus heating and automate each function separately. A main device carries the
shared sensors and reports faults in plain language rather than as a bare number. You need Modbus TCP enabled
on the pump (menu 7.5.9) and the pump on the same network as your Homey.
Setup notes, supported models, what differs between them, and troubleshooting are in the Homey Community topic
linked on this page. Changing settings on a heat pump can affect how it runs, so take the same care you would
in myUplink or on the pump itself.
Based on the original app by Jan Sparud.
Appareils pris en charge
Cartes Flow
Cliquez sur un appareil ci-dessus pour afficher uniquement les cartes Flow associées.
Quand...
Nibe S-Series
Désactivé
Nibe S-Series
L'alarme générique s'est activée
Nibe S-Series
L'alarme générique s'est désactivée
Nibe S-Series
L'énergie a changé
Nibe S-Series
La température a changé
Nibe S-Series
La température cible a été modifiée
Nibe S-Series
An alarm occurred
Fires when the heat pump reports a new alarm. Use the alarm description token to see what happened.
Nibe S-Series
Operating priority changed
Fires when the heat pump switches what it is producing (hot water, heating, pool, cooling, off). The reason token explains why in plain language — which threshold the pump actually reached, with the numbers behind it.
Nibe S-Series
Register changed
Fires when the selected register's value changes. Only registers with a fixed set of modes (operating mode, hot water demand, priority, fan mode) can be picked.
Nibe S-Series
Register turned on
Fires when the selected on/off register switches on.
Nibe S-Series
Register turned off
Fires when the selected on/off register switches off.
Et...
Nibe S-Series
Est activé
Nibe S-Series
L'alarme générique est en marche
Nibe S-Series
Value of Register is Comparison Value
Compares any readable numeric register against a value. Useful for readings that have no card of their own, such as degree minutes or compressor frequency.
Nibe S-Series
Register is enabled
Checks any on/off register, picked by name. Prefer the device’s own on/off condition cards — this is the escape hatch.
Advanced
Nibe S-Series
Operating mode is Mode
Operating mode: auto, manual or immersion heater only.
Nibe S-Series
Priority is Mode
What the pump is producing right now (heating, hot water, pool…).
Nibe S-Series
Fan mode is Mode
Currently active fan mode.
Alors...
Nibe S-Series
Activer
Nibe S-Series
Désactiver
Nibe S-Series
Alterner activé ou désactivé
Nibe S-Series
Définir la température °C
Nibe S-Series
Set the minimum supply temperature to Value
Lowest supply temperature the pump may produce (climate system 1). Accepts 5 to 80 °C.
Nibe S-Series
Set the maximum supply temperature to Value
Highest supply temperature the pump may produce (climate system 1). Accepts 5 to 80 °C.
Nibe S-Series
Set the outdoor temperature that starts cooling to Value
Outdoor temperature where automatic mode starts cooling. Accepts -20 to 40 °C.
Nibe S-Series
Set the outdoor temperature that stops heating to Value
Outdoor temperature where automatic mode stops heating. Accepts -20 to 40 °C.
Nibe S-Series
Set the outdoor temperature that stops the immersion heater to Value
Outdoor temperature where automatic mode stops the immersion heater. Accepts -25 to 40 °C.
Nibe S-Series
Set the heating period time to Value
How long the pump makes heating before switching demand. Accepts 0 to 180 minutes.
Nibe S-Series
Set the compressor start degree minutes to Value
Degree minutes at which the compressor starts heating. Accepts -1000 to -30 °Cmin.
Nibe S-Series
Set the immersion heater start difference to Value
How many degree minutes below the compressor start the immersion heater joins in. Accepts 100 to 2000 °Cmin.
Nibe S-Series
Set the cooling degree minutes to Value
Accumulated cooling surplus that decides when cooling starts. Accepts -3000 to 3000 °Cmin.
Nibe S-Series
Set the hot water start temperature (Small) to Value
Charging start temperature for the Small demand mode. Accepts 5 to 55 °C.
Nibe S-Series
Set the hot water stop temperature (Small) to Value
Charging stop temperature for the Small demand mode. Accepts 5 to 60 °C.
Nibe S-Series
Set the hot water start temperature (Large) to Value
Charging start temperature for the Large demand mode. Accepts 5 to 70 °C.
Nibe S-Series
Set the hot water stop temperature (Large) to Value
Charging stop temperature for the Large demand mode. Accepts 5 to 70 °C.
Nibe S-Series
Set the periodic hot water stop temperature to Value
Stop temperature for the periodic anti-legionella charge. Reaching it usually needs the immersion heater — a compressor alone tops out in the high 50s. Accepts 55 to 70 °C.
Nibe S-Series
Set the hot water start temperature to Value
Tank temperature where hot water charging starts. Accepts 5 to 60 °C.
Nibe S-Series
Set the hot water stop temperature to Value
Tank temperature where hot water charging stops. Accepts 5 to 65 °C.
Nibe S-Series
Set the pool period time to Value
How long the pump heats the pool before switching demand. Accepts 0 to 180 minutes.
Nibe S-Series
Set the normal fan speed to Value
Normal speed of the exhaust air fan. Accepts 0 to 1, where 1 is full speed.
Nibe S-Series
Set the pool start temperature to Value
Pool temperature where heating starts. Accepts 10 to 35 °C.
Nibe S-Series
Set the pool stop temperature to Value
Pool temperature where heating stops. Accepts 10 to 35 °C.
Nibe S-Series
Reset the alarm
Acknowledge and reset an active alarm on the pump.
Nibe S-Series
Set operating mode Mode
Operating mode: auto, manual or immersion heater only.
Nibe S-Series
Set price influence on heating to Influence
How strongly Smart Price Adaption may move the indoor temperature. 1 is barely, 10 is as much as the pump allows.
Nibe S-Series
Set price influence on hot water to Influence
How strongly Smart Price Adaption may shift hot water charging towards cheaper hours. Runs 1 to 4, not 1 to 10 like heating.
Nibe S-Series
Set price influence on pool heating to Influence
How strongly Smart Price Adaption may shift pool heating towards cheaper hours. 0 leaves pool heating alone entirely.
Nibe S-Series
Set price influence on cooling to Influence
How strongly Smart Price Adaption may shift cooling towards cheaper hours. 0 leaves cooling alone entirely.
Nibe S-Series
More hot water – State
More hot water: a one-time 2-hour boost
Nibe S-Series
Night cooling – State
Night cooling using the exhaust air fan
Nibe S-Series
Periodic hot water – State
Enable the periodic hot water boost
Nibe S-Series
Pool heating – State
Enable pool heating
Nibe S-Series
Allow immersion heater – State
Allow the electric immersion heater for heating. Hot water has its own separate switch.
Nibe S-Series
Allow heating – State
Allow heating operation
Nibe S-Series
Allow cooling – State
Allow cooling operation
Nibe S-Series
Allow hot water – State
Allow hot water. Off disables all hot water, including the More hot water boost
Nibe S-Series
Set value of Register to Value
Writes any writable Modbus register, picked by name. Prefer the named cards ("Set the heat curve to …") — this is the escape hatch for registers that have none. Values outside the register’s range are rejected.
Advanced
Nibe S-Series
Enable Register
Switches on any writable on/off register, picked by name. Prefer the device’s own on/off cards — this is the escape hatch.
Advanced
Nibe S-Series
Disable Register
Switches off any writable on/off register, picked by name. Prefer the device’s own on/off cards — this is the escape hatch.
Advanced
Assistance
Vous avez un problème avec cette appli ? Contacter le développeur ici.
Nouveautés
Version 1.0.1 — Nibe Live reaches 1.0 — the first version published on the Homey App Store. Everything before this was a test release, so if you are already running the app, this is the same app, out of testing. One fix comes with it: when the app explains a finished hot water charge, it now names the temperature that charge was actually aiming for. A "More hot water" boost charges to the Large stop temperature whatever demand mode you have selected, and the periodic charge has a target of its own — so charges that used to look like they overshot, or stopped short, are explained correctly.
Nibe Live
Nibe Live n’est pas compatible avec le Homey sélectionné.
Nibe Live va s’installer sur Homey dans un instant.
Journal des modifications
Nous enverrons un merci à Love Thyresson !
Nous ferons savoir à Love Thyresson que vous adorez l’application.
Votre suggestion a été envoyée
Nous informerons Love Thyresson que vous avez envoyé une suggestion.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
