Battery
The battery level changed
Victron Energy
Blue Power
Instantly monitor the battery state of charge, power consumption, power harvest from PV, and mains. Create a flow to get notified if there is an alarm or a warning.
Build control flows to disable or limit the power of the inverter if a car is charging. Easily control the switch position (mode) of your system; Charger Only, Inverter Only, On or Off. All Victron Energy Storage Systems (ESS) standard actions are supported.
Supported devices
Flow cards
Click on a device above to show related Flow cards only.
When...
Battery
The battery charging state changed ...
Battery
The generic alarm turned on
Battery
The generic alarm turned off
Battery
The power changed
Battery
The voltage changed
Battery
The electric current changed
Battery
The temperature changes
Energy Meter
The power changed
Energy Meter
The power meter changed
Energy Meter
Grid surplus changed to [[power]] / [[single_phase]] / [[three_phase]]
EV Charger
The power changed
EV Charger
The electric current changed
EV Charger
The power meter changed
EV Charger
Status changed to [[status]]
PV Inverter
The power changed
Solar Charger
The power changed
Solar Charger
The electric current changed
Solar Charger
The voltage changed
Solar Charger
The power meter changed
Tank sensor
Status changed to [[status]]
Tank sensor
Tank level changed to [[level]]
Temperature sensor
The temperature changes
Temperature sensor
The humidity changed
Temperature sensor
The pressure changed
Temperature sensor
The voltage changed
Temperature sensor
Status changed to [[status]]
Victron GX
The power changed
Victron GX
Alarm status changed to [[status]] with [[alarms]] and [[warnings]]
Victron GX
Dynamic ESS mode changed to Mode
Victron GX
Input source changed to [[source]]
Victron GX
Switch position changed
Victron GX
VE Bus status changed to [[status]]
And...
Battery
The battery charging state is ...
Battery
The generic alarm is on
Battery
Time since last full charge is less than Time (seconds)
Victron GX
AC inputs are below Power (W)
Victron GX
AC loads are below Power (W)
Victron GX
AC outputs are below Power (W)
Victron GX
Max charge current is Condition Current (A)
Victron GX
Consumption power is below Power (W)
Victron GX
Excess solar power is below Power (W)
Victron GX
Max grid feed-in power is Condition Power (W)
Victron GX
Grid power is below Power (W)
Victron GX
Grid setpoint is Condition Power (W)
Victron GX
Input source is Source
Victron GX
Max discharge power is Condition Power (W)
Victron GX
ESS Minimum SoC (unless grid fails) is Condition SoC (%)
Victron GX
Scheduled charging is enabled for schedule Schedule
Victron GX
Solar power is below Power (W)
Victron GX
Switch position is Mode
Victron GX
VE Bus status is Status
Then...
EV Charger
Set EV charger max current to Current (A)
Used for chargers in manual mode. Sets the maximum charge current
EV Charger
Set EV charger mode to Mode
Victron GX
Create charging schedule Schedule for Day at Start time with duration Duration or SoC SoC
Creates a charging schedule. Please note you need to enter your GX device's root password in the device settings.
Victron GX
Disable charging schedule Schedule
Disables a charging schedule. Please note you need to enter your GX device's root password in the device settings.
Victron GX
Enable charging schedule Schedule
Enables a charging schedule. Please note you need to enter your GX device's root password in the device settings.
Victron GX
Limit charge current to Current (A)
Sets the maximum charge current (defined under the DVCC section).
Victron GX
Limit grid feed-in power to Power (W)
Victron GX
Limit AC import to Current (A) when peakshaving
Passing value -1 will disable the limit
Victron GX
Limit discharge power to Power (W)
Sets the maximum inverter power (defined under ESS).
Victron GX
Set batteryLife state to Mode
Victron GX
Set dynamic ESS mode to Mode
Victron GX
Set multiphase regulation state to Mode
Victron GX
Switch relay 1 to State
Victron GX
Switch relay 2 to State
Victron GX
Set switch position to Mode
Victron GX
Update grid setpoint to Power (W)
Sets the grid setpoint (defined under ESS).
Victron GX
Update minimum SoC to SoC (%)
Sets the minimum SoC, unless grid fails (defined under ESS).
Support
Having an issue with this app? Contact the developer here.
What’s new
Version 1.4.5 — Fixed problem with multiple temperature sensors of the same type
Victron Energy
Victron Energy is not compatible with the selected Homey.
Victron Energy will install on Homey shortly.
Changelog
We’ll send a thank you to Richard Barkestam!
We’ll let Richard Barkestam know you love the app. Maybe consider supporting Richard Barkestam by making a donation?
Donate to Richard Barkestam
The developer of Victron Energy accepts donations.
Make a donation to say thanks!
Your suggestion has been sent
We’ll notify Richard Barkestam you’ve sent a suggestion.
