Battery
배터리 수준이 변경되면
Victron Energy
Blue Power
Instantly monitor the battery state of charge, power consumption, power harvest from PV, and mains. Create a flow to get notified if there is an alarm or a warning.
Build control flows to disable or limit the power of the inverter if a car is charging. Easily control the switch position (mode) of your system; Charger Only, Inverter Only, On or Off. All Victron Energy Storage Systems (ESS) standard actions are supported.
지원되는 디바이스
Flow 카드
위의 디바이스를 클릭하면 관련 Flow 카드만 표시됩니다.
언제...
Battery
배터리 충전 상태가 변경되면 ...
Battery
알람이 켜지면
Battery
알람이 꺼지면
Battery
소비 전력이 변경되면
Battery
전압이 변경되면
Battery
전류가 변경되면
Battery
온도가 변경되면
Energy Meter
소비 전력이 변경되면
Energy Meter
전력량이 변경되면
Energy Meter
Grid surplus changed to [[power]] / [[single_phase]] / [[three_phase]]
EV Charger
충전이 시작되면
EV Charger
충전이 중지되면
EV Charger
소비 전력이 변경되면
EV Charger
전류가 변경되면
EV Charger
전력량이 변경되면
EV Charger
전기차 충전기 충전 상태가 변경되면 ...
EV Charger
Status changed to [[status]]
PV Inverter
소비 전력이 변경되면
Solar Charger
소비 전력이 변경되면
Solar Charger
전류가 변경되면
Solar Charger
전압이 변경되면
Solar Charger
전력량이 변경되면
Tank sensor
Status changed to [[status]]
Tank sensor
Tank level changed to [[level]]
Temperature sensor
온도가 변경되면
Temperature sensor
습도가 변경되면
Temperature sensor
기압이 변경되면
Temperature sensor
전압이 변경되면
Temperature sensor
Status changed to [[status]]
Victron GX
소비 전력이 변경되면
Victron GX
Alarm status changed to [[status]] with [[alarms]] and [[warnings]]
Victron GX
Dynamic ESS mode changed to Mode
Victron GX
Input source changed to [[source]]
Victron GX
Switch position changed
Victron GX
VE Bus status changed to [[status]]
그리고...
Battery
배터리 충전 상태가 다음과 같으면 ...
Battery
알람이 켜지면
Battery
Time since last full charge is less than Time (seconds)
EV Charger
충전 중이면
EV Charger
전기차 충전기 충전 상태가 다음과 같음 ...
Victron GX
AC inputs are below Power (W)
Victron GX
AC loads are below Power (W)
Victron GX
AC outputs are below Power (W)
Victron GX
Max charge current is Condition Current (A)
Victron GX
Consumption power is below Power (W)
Victron GX
Excess solar power is below Power (W)
Victron GX
Max grid feed-in power is Condition Power (W)
Victron GX
Grid power is below Power (W)
Victron GX
Grid setpoint is Condition Power (W)
Victron GX
Input source is Source
Victron GX
Max discharge power is Condition Power (W)
Victron GX
ESS Minimum SoC (unless grid fails) is Condition SoC (%)
Victron GX
Scheduled charging is enabled for schedule Schedule
Victron GX
Solar power is below Power (W)
Victron GX
Switch position is Mode
Victron GX
VE Bus status is Status
그러면...
EV Charger
충전 시작
EV Charger
충전 중지
EV Charger
Set EV charger max current to Current (A)
Used for chargers in manual mode. Sets the maximum charge current
EV Charger
Set EV charger mode to Mode
Victron GX
Create charging schedule Schedule for Day at Start time with duration Duration or SoC SoC
Creates a charging schedule. Please note you need to enter your GX device's root password in the device settings.
Victron GX
Disable charging schedule Schedule
Disables a charging schedule. Please note you need to enter your GX device's root password in the device settings.
Victron GX
Enable charging schedule Schedule
Enables a charging schedule. Please note you need to enter your GX device's root password in the device settings.
Victron GX
Limit charge current to Current (A)
Sets the maximum charge current (defined under the DVCC section).
Victron GX
Limit grid feed-in power to Power (W)
Victron GX
Limit AC import to Current (A) when peakshaving
Passing value -1 will disable the limit
Victron GX
Limit discharge power to Power (W)
Sets the maximum inverter power (defined under ESS).
Victron GX
Set batteryLife state to Mode
Victron GX
Set dynamic ESS mode to Mode
Victron GX
Set multiphase regulation state to Mode
Victron GX
Switch relay 1 to State
Victron GX
Switch relay 2 to State
Victron GX
Set switch position to Mode
Victron GX
Update grid setpoint to Power (W)
Sets the grid setpoint (defined under ESS).
Victron GX
Update minimum SoC to SoC (%)
Sets the minimum SoC, unless grid fails (defined under ESS).
Victron VRM
Set Dynamic ESS to Mode
Switches Dynamic ESS between Green mode and Trade mode via the VRM API. Requires the VRM device to be added and authenticated.
지원
이 앱에 문제가 있습니까? 개발자에게 문의하려면 여기를 클릭하세요..
새로운 기능
버전 1.5.6 — VRM devices can now be connected with a personal access token created in the VRM Portal. This is the only method that works for accounts migrated to Victron OneID, where Victron no longer accepts email and password for the API, and it also avoids the 2FA code prompt. Failed VRM logins now show the reason reported by VRM instead of a generic error.
업데이트 로그
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
