eAir
A B alarm went off
Exvent
Fresh air, on autopilot.
Your ventilation runs around the clock, and with Homey it can adapt to your day. Keep an eye on the indoor climate and the filter, and let Flows turn the ventilation down when nobody is home and back up after a shower. The app works with Exvent eWind and eAir, and with Exvent units that have EDA automation through a Freeway WEB adapter.
지원되는 디바이스
Flow 카드
위의 디바이스를 클릭하면 관련 Flow 카드만 표시됩니다.
언제...
The unit reports a class B alarm, such as the filter or service reminder. The alarm token says which.
eAir
Mode changed to ...
Fires when the mode changes, whether from Homey, a flow, the unit panel or the unit itself. A change on the panel can take up to a minute to show. Enhanced ventilation also covers the unit's own CO₂ and humidity boost.
eAir
Heat exchanger changed to ...
eAir
Heating coil changed to ...
eAir
An A alarm went off
The unit reports a serious alarm and stops. The alarm token says which.
eAir
Days until filter change dropped below Days
Fires once when the countdown to the filter change passes the number.
EDA
A B alarm went off
The unit reports a class B alarm, such as dirty filters or the service reminder. The alarm token says which.
EDA
Mode changed to ...
Fires when the mode changes, whether from Homey, a flow, the unit panel or the unit itself. A change on the panel can take up to a minute to show.
EDA
Heat exchanger changed to ...
EDA
Heating changed to ...
EDA
Defrosting started
The heat pump started defrosting. It stops heating or cooling while it does.
EDA
Defrosting ended
EDA
Cooling started
EDA
Cooling stopped
EDA
An A alarm went off
The unit reports a serious alarm, such as frost or fire risk, and stops. The alarm token says which.
eWind
A B alarm went off
The unit reports a class B alarm, such as the filter or service reminder. The alarm token says which.
eWind
Mode changed to ...
Fires when the mode changes, whether from Homey, a flow, the unit panel or the unit itself. A change on the panel can take up to a minute to show. Enhanced ventilation also covers the unit's own CO₂ and humidity boost.
eWind
Heat exchanger changed to ...
eWind
Heating coil changed to ...
eWind
An A alarm went off
The unit reports a serious alarm and stops. The alarm token says which.
eWind
Days until filter change dropped below Days
Fires once when the countdown to the filter change passes the number.
그리고...
eAir
Mode is ...
eAir
Heat exchanger is ...
eAir
Heating coil is ...
eAir
A alarm is active
eAir
B alarm is active
eAir
Fan speed level is ...
eAir
Heating coil is enabled
eAir
The unit is boosting on its own
The unit's own boost on CO₂, humidity or temperature. Enhanced ventilation chosen in Homey or on the panel does not count.
EDA
Mode is ...
EDA
Heat exchanger is ...
EDA
Heating is ...
EDA
Defrosting is in progress
EDA
Cooling is active
EDA
A alarm is active
EDA
B alarm is active
eWind
Mode is ...
eWind
Heat exchanger is ...
eWind
Heating coil is ...
eWind
A alarm is active
eWind
B alarm is active
eWind
Fan speed level is ...
eWind
Heating coil is enabled
eWind
The unit is boosting on its own
The unit's own boost on CO₂, humidity or temperature. Enhanced ventilation chosen in Homey or on the panel does not count.
그러면...
eAir
Set eco mode to ...
eAir
Set Heating coil enabled to ...
Lets the unit use the heating coil, or keeps it from doing so.
eAir
Set target temperature to °C
eAir
Set mode to ...
Boost ends by itself after the boost duration, and fireplace mode after the fireplace duration in the device settings. Enhanced ventilation stays on until the mode is changed. Off stops the unit.
eAir
Reset filter change reminder
Resets the unit's filter/service day counter to 0. Use after replacing the filter.
eAir
Start fireplace mode for min
Sets the fireplace duration on the unit and starts fireplace mode. The duration is kept for the next time too.
EDA
... heating
Allows or blocks heating of the supply air. Stored on the unit.
EDA
Set target temperature to °C
EDA
Set mode to ...
Boost ends by itself after the boost duration, and overpressure after the overpressure duration in the device settings. Off stops the unit.
EDA
... cooling
Allows or blocks cooling of the supply air. Stored on the unit.
EDA
Block heating above °C
Heating is blocked while the outdoor temperature is above this temperature. Stored on the unit.
EDA
Block cooling below °C
Cooling is blocked while the outdoor temperature is below this temperature. Stored on the unit.
EDA
Set fan level to %
Sets the unit's fan level, just like its panel. Only for units with EC fans. Boost, overpressure and a running heat pump can raise it for a while.
EDA
Set overpressure duration to min
How many minutes overpressure stays active before the unit returns to normal operation. Stored on the unit, and applies the next time overpressure starts.
EDA
Start boost for min
Sets the boost duration on the unit and starts boost. The duration is kept for the next boost too.
EDA
Start overpressure for min
Sets the overpressure duration on the unit and starts overpressure. The duration is kept for the next time too.
eWind
Set eco mode to ...
eWind
Set Heating coil enabled to ...
Lets the unit use the heating coil, or keeps it from doing so.
eWind
Set target temperature to °C
eWind
Set mode to ...
Boost ends by itself after the boost duration, and fireplace mode after the fireplace duration in the device settings. Enhanced ventilation stays on until the mode is changed. Off stops the unit.
eWind
Reset filter change reminder
Resets the unit's filter/service day counter to 0. Use after replacing the filter.
eWind
Start boost for min
Sets the boost duration on the unit and starts boost. The duration is kept for the next boost too.
eWind
Start fireplace mode for min
Sets the fireplace duration on the unit and starts fireplace mode. The duration is kept for the next time too.
지원
이 앱에 문제가 있습니까? 개발자에게 문의하려면 여기를 클릭하세요..
새로운 기능
버전 5.0.0 — Commands no longer get lost: they are sent again when the unit is slow, and a Flow card fails visibly when the unit cannot be reached. The device shows a warning when the unit stops answering, and reconnects faster. Mode changed now also fires when a Flow sets the mode, a stop from the panel shows as Off, and boost or fireplace mode started from Away ends in Home. Settings that do not reach the unit are no longer saved, and the fireplace duration now shows the one the unit keeps after a power cut. New: A alarm with the alarm text, boost as the quick action and its duration, cards that start boost or fireplace mode for a number of minutes, heat recovery and after-heating in percent, season, eAir fan speeds, filter reset under Maintenance, mode history in Insights and more Flow cards. Pairing now checks the connection first.
업데이트 로그
Vegard Fladby 님에게 고맙다는 인사를 전해드리겠습니다!
Vegard Fladby 님께 앱을 잘 사용하고 있다고 알려주세요.
제안이 전송되었습니다.
제안을 보내주셨다고 Vegard Fladby 님에게 알리겠습니다.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
