EV charger
Tændt
OCPP Bridge
Smart charging from Homey, with your charging provider still on board.
Advarsel! Denne app fungerer muligvis ikke ordentligt.
Denne app er ved at blive testet og er aldrig blevet anmeldt. Den fungerer muligvis ikke som forventet.
Vær ekstra forsigtig, når du installerer denne app.
OCPP Bridge makes Homey the place where your electric car charges smartly. Your home charger connects straight to Homey over your own network, so you can see what it is doing at a glance and let your Flows decide when and how fast to charge, for example on cheap hours or on your own solar power.
Most home chargers are also linked to a charging provider for invoices, charge cards or an app. With OCPP Bridge that link stays intact: Homey sits in the middle and passes everything on, so your provider keeps working exactly as before, and the app quietly repairs the connection when it drops. Setup takes a few minutes and needs no technical knowledge: Homey shows the address to enter in your charger and finds the charger by itself. You need a Homey Pro and a charger that supports OCPP 1.6 (JSON), which most modern wallboxes do.
Understøttede enheder
Flow-kort
Klik på en enhed ovenfor for kun at vise relaterede Flow-kort.
Når...
EV charger
Slukket
EV charger
Strømmen ændrede sig
EV charger
Strømmåleren ændrede sig
EV charger
Den elektriske strøm ændrede sig
EV charger
Den elektriske spænding ændrede sig
EV charger
Den generiske alarm blev aktiveret
EV charger
Den generiske alarm blev deaktiveret
EV charger
Begyndte at oplade
EV charger
Stoppede med at oplade
EV charger
Elbilopladerens opladningstilstand er ændret ...
EV charger
Charging started
EV charger
Charging stopped
EV charger
A car was plugged in
EV charger
The car was unplugged
EV charger
Charger connection lost
The charger lost its connection to Homey, for example because of a power cut or wifi problem.
EV charger
Charger connection restored
EV charger
Charging was paused
A running session stopped drawing power for at least 2 seconds. The reason tag is charger when the charger holds the pause, for example a 0 A limit, its own schedule or app, and car when the car holds it, for example because it is full.
EV charger
Charging resumed
A paused session draws power again for at least 2 seconds. Not fired for a new session; use Charging started for that. The reason tag says who held the pause: charger or car.
EV charger
The charging limit changed
The charger accepted a new current limit from Homey. 0 A means Homey paused charging. The source tag says which card or automation set it.
EV charger
A charging session ended
The charger ended a session, for example because the car was unplugged or charging was stopped. Pauses do not end a session. Energy and duration are 0 when Homey did not see the start of the session. Card ID is the card the charger reported for the session, or the Card ID for Homey starts from the device settings when Homey started it; empty when unknown. Use it with the energy to bill a tenant.
EV charger
The car stopped charging
The car stopped drawing power, usually because it is full or finished its own schedule. Use it to stop a Flow that adjusts the current. Fires once when the car holds the pause, or the session is finishing, with almost no current for the time set in the device settings, 2 minutes by default. Not for a pause by Homey or by the charger. Fires again only after charging started again. The reason tag is full or finished, or session ended.
OCPP Bridge
Connection alert
Fires when the charging provider or charger connection has been down for a while, was restored automatically, or could not be restored. Use the message tag in a Flow that sends a push notification.
Og...
EV charger
Er tændt
EV charger
Den generiske alarm er tændt
EV charger
Oplader
EV charger
Elbilopladerens opladningstilstand er ...
EV charger
Charger is charging
EV charger
Charging provider is connected
Whether Homey currently has a working connection to the charging provider set for this charger.
EV charger
Charging current limit is above Amps A
Compares with the last limit Homey set with the Set maximum charging current or Adjust charging cards; 0 A while Homey paused charging. If Homey has not set one yet, the highest charging current from the device settings is used.
EV charger
Charging is paused
A session is running but not drawing power, held by the charger or by the car.
EV charger
Pause is held by the Held by
Charger: the charger itself holds the pause, for example a 0 A limit, its own app or schedule. Car: the car holds it, for example because it is full or has its own schedule. Homey can only lift a pause held by the charger.
EV charger
A charging session is running
True from the start of a session until it ends, also while it is paused.
EV charger
The car has stopped charging
The car stopped drawing power, usually because it is full or finished its own schedule. Use it to stop a Flow that adjusts the current. True in the same state as the card The car stopped charging, once it held for the time set in the device settings; false while it charges, after it is unplugged, during a pause by Homey or by the charger, and while the charger is not connected.
Så...
EV charger
Tændt
EV charger
Slukket
EV charger
Tænd eller sluk
EV charger
Begynd at oplade
EV charger
Stop med at oplade
EV charger
Start charging
A car must be plugged in. A paused session is resumed instead, except a pause that a smart card such as Protect the main fuse or Charge from solar surplus set for lack of power while it still runs: that card resumes by itself after its wait, so Start charging changes nothing then. In a Flow that runs every few seconds, put the condition A charging session isn't running before this card. Homey's own Start charging card for EV chargers works like the on/off switch and always lifts the pause.
EV charger
Resume charging
For a paused session: Homey sends the last current limit it set again, at least the lowest current plus the extra resume current, or the highest current if it never set one. If the charger stays paused, Homey tries one amp more by itself, at most twice, and only then restarts the session if that is on in the device settings. Repeated calls are limited to one attempt per 30 seconds by default. If the car holds the pause, for example because it is full, Homey cannot override it. This card always lifts a pause by Homey, also one a smart card set for lack of power; in a Flow that runs every few seconds next to a smart card, use Start charging with the condition A charging session isn't running instead. To start a new session, use Start charging.
EV charger
Stop charging
Ends the session. To keep the session and only stop the power, use Pause charging. Homey also shows its own Stop charging card for every EV charger; in this app both do exactly the same.
EV charger
Set maximum charging current to Amps A
Limits how fast the car charges, for example to match solar surplus. The value is kept between the lowest and highest current set in the device settings; a charger cannot charge slower than its lowest step. To pause, use Pause charging.
EV charger
Pause charging
Pauses with a 0 A limit while the session keeps running; Resume charging continues it. If the charger does not accept 0 A, the card shows an error, unless Pausing may end the session is on in the device settings: then the session is stopped.
EV charger
Adjust charging to Available power in W W available on Phases
For solar surplus: give the power the car may use in watts. Homey works out the current, lowers it right away, raises it only after the higher value was asked for some time, pauses below the lowest current and resumes with a little extra current so the charger really continues. Run it every 10 to 60 seconds; the waits are in the device settings. Easier: Charge from solar surplus takes your meter's grid power directly.
EV charger
Adjust charging to Available current per phase in A A available per phase
For main fuse protection: give the current per phase the car may use. Decimals are rounded down, so 9.9 A becomes 9 A. Lowering happens right away, raising only after the higher value was asked for some time, and below the lowest current Homey pauses or holds the minimum, as set in the device settings. After a pause Homey resumes with a little extra current and checks that the charger really continues. Easier: Protect the main fuse does the calculation for you.
EV charger
Protect the main fuse with house currents House current L1 in A House current L2 in A House current L3 in A A and fuse Fuse size in A A
Give the current per phase your meter measures, including the car; tags of your meter work. Homey takes off the charger's own current per phase, keeps the safety margin from the device settings below the fuse and sets the car to what is left on the busiest phase, rounded down. Lowering is immediate, raising waits, below the lowest current Homey pauses and resumes later. Leave the fuse empty to use the device setting. Safe to run every 10 seconds; negative values are fine. For a second fuse, such as a sub-panel, or a second charger use Protect several fuses.
EV charger
Charge from solar surplus with grid power Grid power in W W, home battery Home battery power in W W and reserve Reserve in W W
Give the grid power of your meter; a tag works. By default importing is positive and exporting negative; change Grid power sign in the device settings if your meter reports it the other way. Give the power of your home battery: positive while it charges, negative while it discharges, so the car can use the surplus the battery would otherwise take. Leave empty without a battery. Homey adds the charger's own power and charges with what would otherwise go to the grid or the battery, minus the reserve. Below the lowest current it pauses and resumes once there was enough sun for a while. Leave the reserve empty to use the device setting. Safe to run every 10 seconds.
EV charger
Charge from solar surplus with grid power Grid power in W W, home battery Home battery power in W W and reserve Reserve in W W, protect the fuse with house currents House current L1 in A House current L2 in A House current L3 in A A and fuse Fuse size in A A
Solar surplus and main fuse protection in one card: Homey works out both limits and uses the lowest, so the two never fight. Fill in the grid power and the meter's current per phase, including the car; tags work. Give the power of your home battery: positive while it charges, negative while it discharges, so the car can use the surplus the battery would otherwise take. Leave empty without a battery. The support report says which one is limiting. Leave the reserve or fuse empty to use the device settings. Safe to run every 10 seconds. For several fuses or a charger with priority use Protect several fuses; run one fuse or solar card per charger.
EV charger
Protect several fuses: main fuse Main fuse size in A A with house currents House current L1 in A House current L2 in A House current L3 in A A, extra fuse 1 Extra fuse 1 size in A A with Extra fuse 1 current L1 in A Extra fuse 1 current L2 in A Extra fuse 1 current L3 in A A, extra fuse 2 Extra fuse 2 size in A A with Extra fuse 2 current L1 in A Extra fuse 2 current L2 in A Extra fuse 2 current L3 in A A, extra fuse 3 Extra fuse 3 size in A A with Extra fuse 3 current L1 in A Extra fuse 3 current L2 in A Extra fuse 3 current L3 in A A, lower priority Charger with lower priority and Second charger with lower priority
For a main fuse with fuses behind it, such as a sub-panel, and for two chargers where this one has priority. Per fuse give the current per phase its meter measures, including this charger; tags work. Leave the size empty to use the device setting, Main fuse size or Extra fuse 1-3 size; an extra fuse without currents is not used. Homey sets the car to what the tightest fuse and phase leaves, rounded down, with the safety margin from the device settings. The current of a charger with lower priority is not counted on the main fuse, so this charger may use it; give that charger Protect the main fuse, so it gets what is left. Use one fuse or solar card per charger. Safe to run every 10 seconds.
EV charger
Ask the charger for a fresh reading now
Asks the charger to send its power, current and energy right away, for Flows that need a fresh value. A charger that does not support this gives an error.
Support
Har du et problem med denne app? Kontakt udvikleren ved at sende en e-mail.
Hvad er nyt
Version 1.1.18 — The solar surplus cards have a new optional field Home battery power (positive while it charges, negative while it discharges), so the surplus your home battery would take goes to the car and the car never drains the battery. New setting Home battery power sign. The history and the diagnostics report show every term, and a new setup check warns when the grid power stays near zero while the car waits.
OCPP Bridge
OCPP Bridge er ikke kompatibel med den valgte Homey.
OCPP Bridge bliver snart installeret på Homey.
Ændringslog
Vi sender en tak til Wisse Koelman!
Vi lader Wisse Koelman vide, at du elsker appen. Overvej måske at støtte Wisse Koelman ved at give en donation?
Donér til Wisse Koelman
Udvikleren af OCPP Bridge tager imod donationer.
Giv et bidrag for at sige tak!
Dit forslag er blevet sendt
Vi giver Wisse Koelman besked, når du har sendt et forslag.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
