Luxtronik Heat Pump
Måltemperaturen ändrades
Luxtronik Heat Pump Manager
Comfort and hot water, perfectly tuned.
Luxtronik Heat Pump Manager brings your Luxtronik-based heat pump into Homey — with full sensor visibility, smart flow integration, and direct control over heating and hot water. Whether you want to automate hot water heating with solar surplus, adjust operating modes, or get notified when your heat pump changes state, this app gives you the tools to do it.
Compatible with Alpha-Innotec, CTA, Novelan, Roth, Elco, Buderus, Nibe, Wolf Heiztechnik and many other Luxtronik-based systems. The app uses the standardised Luxtronik interface and works across different system configurations and firmware versions.
Enheter som stöds
Flow-kort
Klicka på en enhet ovan för att visa endast relaterade Flow-kort.
När...
Luxtronik Heat Pump
Temperaturen ändrades
Luxtronik Heat Pump
Det generiska larmet är aktiverat
Luxtronik Heat Pump
Det generiska larmet är inaktiverat
Luxtronik Heat Pump
Cooling mode changed
Luxtronik Heat Pump
Hot Water Boost (Party) started
Luxtronik Heat Pump
Hot Water Boost (Auxiliary) started
Luxtronik Heat Pump
Heating mode changed
Luxtronik Heat Pump
Hot water mode changed
Luxtronik Heat Pump
Heat pump state changed
Luxtronik Heat Pump
Error occurred
Luxtronik Heat Pump
Hot Water Boost (Auxiliary Heating) ended
Luxtronik Heat Pump
Hot Water Boost (Party) ended
Luxtronik Heat Pump
Device became unavailable
Luxtronik Heat Pump
Device became available again
Luxtronik Heat Pump
Thermal Disinfection ended
Luxtronik Heat Pump
Error cleared
Luxtronik Heat Pump
Outdoor temperature dropped below Temperature (°C) °C
Luxtronik Heat Pump
Outdoor temperature rose above Temperature (°C) °C
Luxtronik Heat Pump
Room temperature dropped below Temperature (°C) °C
Luxtronik Heat Pump
Room temperature rose above Temperature (°C) °C
Och...
Luxtronik Heat Pump
Det generiska larmet är på
Luxtronik Heat Pump
The cooling mode is Mode
Luxtronik Heat Pump
The heating mode is Mode
Luxtronik Heat Pump
The hot water mode is Mode
Luxtronik Heat Pump
The heat pump state is State
Luxtronik Heat Pump
Thermal disinfection is active
Luxtronik Heat Pump
Hot water boost (auxiliary heating) is active
Luxtronik Heat Pump
Hot water boost (party) is active
Luxtronik Heat Pump
Device is available
Luxtronik Heat Pump
Heating status is Status
Luxtronik Heat Pump
Hot water status is Status
Luxtronik Heat Pump
Outdoor temperature is above Temperature (°C) °C
Luxtronik Heat Pump
Outdoor temperature is below Temperature (°C) °C
Luxtronik Heat Pump
Room temperature is above Temperature (°C) °C
Luxtronik Heat Pump
Room temperature is below Temperature (°C) °C
Då...
Luxtronik Heat Pump
Ställ in temperaturen °C
Luxtronik Heat Pump
Restore hot water hysteresis to configured value
Luxtronik Heat Pump
Set cooling mode to Mode
Luxtronik Heat Pump
Minimize hot water hysteresis (set to 0.5 K)
Luxtronik Heat Pump
Set heating mode to Mode
Luxtronik Heat Pump
Set hot water mode to Mode
Luxtronik Heat Pump
Set heating temperature correction to Correction °C (−5 to +5) °C
Shifts the heating curve up or down. Positive values increase the flow temperature (warmer), negative values decrease it (cooler). Does not change the heating mode.
Luxtronik Heat Pump
Set hot water target temperature to Temperature °C (30 to 65) °C
Luxtronik Heat Pump
Start Hot Water Boost (Auxiliary Heating) for Duration (minutes) minutes
Luxtronik Heat Pump
Stop Hot Water Boost (Auxiliary Heating)
Luxtronik Heat Pump
Start Hot Water Boost (Party) for Duration (minutes) minutes
Luxtronik Heat Pump
Stop Hot Water Boost (Party)
Luxtronik Heat Pump
Set max. outdoor temperature to Temperature °C (10 to 45) °C
Luxtronik Heat Pump
Set heating limit to Temperature °C (5 to 30) °C
Luxtronik Heat Pump
Set return temperature hysteresis to Hysteresis K (0.5 to 10) K
Controls how far the return temperature may drop below the setpoint before the heat pump restarts. A smaller value means tighter control but more frequent compressor cycles.
Luxtronik Heat Pump
Set hot water hysteresis to Hysteresis K (0.5 to 10) K
Controls how far the hot water temperature may drop below the setpoint before the heat pump starts reheating. A smaller value keeps the water closer to the target but increases compressor cycles.
Luxtronik Heat Pump
Enable thermal disinfection
Activates continuous thermal disinfection (legionella protection). The heat pump heats the hot water tank to the disinfection setpoint (default 65 °C) and automatically deactivates once the target is reached.
Luxtronik Heat Pump
Disable thermal disinfection
Deactivates continuous thermal disinfection mode.
Support
Har du problem med den här appen? Kontakta utvecklaren här.
Vad är nytt?
Version 2.1.19 — Improved: right after the data dump it writes at start-up, the app now logs a one-line summary of the most important settings: firmware, room unit and control mode, heating correction, heating curve, heating limit, operating modes, and the hot water setpoint with its maximum and hysteresis. A diagnostics report contains only the end of the log, and the dump used to push these values out of it.
Luxtronik Heat Pump Manager
Luxtronik Heat Pump Manager är inte kompatibelt med vald Homey.
Luxtronik Heat Pump Manager installeras på Homey inom kort.
Ändringslogg
Vi kommer att skicka en tacksamhet till Andi W.!
Vi låter Andi W. veta att du älskar appen. Överväg att stödja Andi W. genom att göra en donation?
Donera till Andi W.
Utvecklaren av Luxtronik Heat Pump Manager tar emot donationer.
Gör en donation för att tacka!
Ditt förslag har skickats
Vi skickar ett meddelande till Andi W. om att du har skickat ett förslag.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
