Samsung Appliance
Mode changed
SmartThings Local
Control Samsung appliances locally, with no cloud in between
Samsung's newer appliances speak a local protocol on your own network, and this app speaks it back. Commands and readings go straight to the appliance's address on your LAN instead of out through SmartThings, so nothing about your home leaves it, and everything keeps working when the internet does not.
Air conditioners, induction cooktops, range hoods and refrigerators are supported, each verified against real hardware — a hood's fan and light, a fridge's temperature per compartment including a convertible one it tells you is currently cooling or freezing, an air conditioner's temperature, mode and comfort settings. All of it is available to a Flow: anything the appliance reports can be a condition, anything it accepts can be an action. Heat control is the one deliberate exception, read-only on cooking appliances, because an automation must never start a burner. Setup is installing it: the app issues its own client certificate on first run, then finds your appliances by searching the network. You can supply your own certificate instead, and the app will never replace it. Roughly 2022 and later models expose the local protocol; older ones keep no local port open and cannot be reached this way.
Enheter som stöds
Flow-kort
Klicka på en enhet ovan för att visa endast relaterade Flow-kort.
När...
Fires on a change, not on every reading that repeats the same value. It cannot tell who made the change: a Flow of your own, the remote, and the appliance's panel all look the same here. To act only on someone else's change, compare the value against what your Flow last set.
Samsung Appliance
An alarm was raised
Fires when the appliance reports a fault or maintenance code, and again when it clears. The code is the appliance's own, not a translation.
Samsung Appliance
Dust bag needs attention cleared
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Dust bag needs attention was raised
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
The filter is back to normal
Fires when the appliance stops asking for the filter — after it has been washed or replaced. The counterpart to the card that fires when it starts asking.
Samsung Appliance
A filter needs attention
Fires when the appliance stops reporting its filter as normal — washable filters ask to be washed, others to be replaced.
Samsung Appliance
Hot surface cleared
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Hot surface was raised
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
A burner is on turned off
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
A burner is on turned on
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
A cycle finished
For appliances that run cycles — washer, dryer, dishwasher, air dresser. Fires on the transition to finished, not repeatedly while idle.
Samsung Appliance
A cycle started
Fires on the transition into running, so an appliance already running does not keep announcing it.
Samsung Appliance
The light turned off
Fires on the transition to off, not on every reading that happens to be off.
Samsung Appliance
The light turned on
Fires on the transition to on, not on every reading that happens to be on.
Samsung Appliance
Fan speed changed
Fires on a change, not on every reading that repeats the same value. It cannot tell who made the change: a Flow of your own, the remote, and the appliance's panel all look the same here. To act only on someone else's change, compare the value against what your Flow last set.
Samsung Appliance
Firmware update available turned off
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Firmware update available turned on
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Machine state changed
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Status changed
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Probe connected turned off
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Probe connected turned on
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Progress changed
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Time remaining changed
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Safety auto-shutoff turned off
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Safety auto-shutoff turned on
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Self check changed
Fires on a change, not on every reading that repeats the same value.
Samsung Appliance
Airflow direction changed
Fires on a change, not on every reading that repeats the same value. It cannot tell who made the change: a Flow of your own, the remote, and the appliance's panel all look the same here. To act only on someone else's change, compare the value against what your Flow last set.
Och...
Samsung Appliance
Absence clean is on
Checks the value as the appliance last reported it.
Samsung Appliance
Absence detection is on
Checks the value as the appliance last reported it.
Samsung Appliance
Absence threshold is at least ... min
Checks the value as the appliance last reported it.
Samsung Appliance
Motion monitoring is on
Checks the value as the appliance last reported it.
Samsung Appliance
Absence power saving is on
Checks the value as the appliance last reported it.
Samsung Appliance
Mode is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Air purify is on
Checks the value as the appliance last reported it.
Samsung Appliance
Air cleanliness is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Action on sensing is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Periodic air sensing is on
Checks the value as the appliance last reported it.
Samsung Appliance
Last air grade is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Sensing is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Active alarm is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Dust bag needs attention is on
Checks the value as the appliance last reported it.
Samsung Appliance
Filter needs attention is on
Checks the value as the appliance last reported it.
Samsung Appliance
Hot surface is on
Checks the value as the appliance last reported it.
Samsung Appliance
Auto dry running is on
Checks the value as the appliance last reported it.
Samsung Appliance
Auto clean is on
Checks the value as the appliance last reported it.
Samsung Appliance
Auto dry progress is at least ... %
Checks the value as the appliance last reported it.
Samsung Appliance
Auto close is on
Checks the value as the appliance last reported it.
Samsung Appliance
Auto empty is on
Checks the value as the appliance last reported it.
Samsung Appliance
Automatic ventilation is on
Checks the value as the appliance last reported it.
Samsung Appliance
Auto fill is on
Checks the value as the appliance last reported it.
Samsung Appliance
A burner is on is on
Checks the value as the appliance last reported it.
Samsung Appliance
Burner level is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Burner state is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Interior light is on
Checks the value as the appliance last reported it.
Samsung Appliance
Child lock is on
Checks the value as the appliance last reported it.
Samsung Appliance
Child lock is on
Checks the value as the appliance last reported it.
Samsung Appliance
Convenient mode is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Convertible compartment is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Cycle running is on
Checks the value as the appliance last reported it.
Samsung Appliance
Dishwasher cycle is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Washes until drum clean is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Dry cycle is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Dry cycle is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Dry level is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Dust PM1.0 is at least ... µg/m³
Checks the value as the appliance last reported it.
Samsung Appliance
Dust PM10 is at least ... µg/m³
Checks the value as the appliance last reported it.
Samsung Appliance
Dust bag usage is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Edge lighting colour is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Edge lighting is on
Checks the value as the appliance last reported it.
Samsung Appliance
Edge lighting brightness is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Fan speed is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Fan level is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Filter usage is at least ... %
Checks the value as the appliance last reported it.
Samsung Appliance
Firmware update available is on
Checks the value as the appliance last reported it.
Samsung Appliance
Heated dry is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Fan speed is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Ice maker is on
Checks the value as the appliance last reported it.
Samsung Appliance
State is arriving by push
Push means the appliance notifies the app the moment something changes. Polling is the fallback, and state can then be up to the poll interval old.
Samsung Appliance
Storage mode is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Racks is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Ripening is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Ripening remaining is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Light brightness is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
The light is on
Checks the light as the appliance last reported it.
Samsung Appliance
Panel brightness is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Machine state is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Avoid direct wind is on
Checks the value as the appliance last reported it.
Samsung Appliance
Mute beep once is on
Checks the value as the appliance last reported it.
Samsung Appliance
Smart Cool Clean is on
Checks the value as the appliance last reported it.
Samsung Appliance
Smart Cool Clean progress is at least ... %
Checks the value as the appliance last reported it.
Samsung Appliance
Operation state code is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Status is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Oven mode is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Pan is on
Checks the value as the appliance last reported it.
Samsung Appliance
Pet filter is on
Checks the value as the appliance last reported it.
Samsung Appliance
Power saving level is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Power is on
Checks the value as the appliance last reported it.
Samsung Appliance
Probe connected is on
Checks the value as the appliance last reported it.
Samsung Appliance
Progress is at least ... %
Checks the value as the appliance last reported it.
Samsung Appliance
Rapid freezing is on
Checks the value as the appliance last reported it.
Samsung Appliance
Rapid cooling is on
Checks the value as the appliance last reported it.
Samsung Appliance
Time remaining is at least ... min
Checks the value as the appliance last reported it.
Samsung Appliance
Rinse cycles is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Sabbath mode is on
Checks the value as the appliance last reported it.
Samsung Appliance
Safety auto-shutoff is on
Checks the value as the appliance last reported it.
Samsung Appliance
Sanitize is on
Checks the value as the appliance last reported it.
Samsung Appliance
Self check running is on
Checks the value as the appliance last reported it.
Samsung Appliance
Self check is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Self check progress is at least ... %
Checks the value as the appliance last reported it.
Samsung Appliance
Smart control enabled is on
Checks the value as the appliance last reported it.
Samsung Appliance
Smart sensing cooling is on
Checks the value as the appliance last reported it.
Samsung Appliance
Sound mode is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Sound volume is at least ...
Checks the value as the appliance last reported it.
Samsung Appliance
Spin speed is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Target humidity is at least ... %
Checks the value as the appliance last reported it.
Samsung Appliance
Set temperature is at least ... °C
Checks the value as the appliance last reported it.
Samsung Appliance
UV sterilisation is on
Checks the value as the appliance last reported it.
Samsung Appliance
Wash cycle is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Wash cycle is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Wash temperature is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Water used is at least ... L
Checks the value as the appliance last reported it.
Samsung Appliance
Water tank alarm is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Water tank light is on
Checks the value as the appliance last reported it.
Samsung Appliance
Welcome lighting is on
Checks the value as the appliance last reported it.
Samsung Appliance
Airflow direction is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Airflow toward people is ...
Checks the value as the appliance last reported it.
Samsung Appliance
Wrinkle prevention is on
Checks the value as the appliance last reported it.
Då...
Samsung Appliance
Turn Absence clean ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Absence power saving ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Mode to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Apply settings: power Power, mode Mode, Target temperature (0 to skip)°C, fan Fan speed, direction Airflow direction, air purify Air purify, comfort Comfort mode
Applies several settings in one card. A setting the appliance already holds is not sent, so re-asserting the same state is quick; the rest are written and confirmed, re-reading the appliance before it starts and after every step so each decides from what the appliance holds now. Everything asked for is verified at the end, including the settings that were skipped. Set a field to "leave unchanged" to skip it, and temperature to 0 to skip that. The operating mode takes priority: each mode only honours some of the others — AI Comfort takes no fan speed or comfort mode, Fan takes no target temperature — and anything the chosen mode will not accept is left alone rather than written and silently ignored.
Samsung Appliance
Turn Air purify ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Auto clean ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Auto close ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Auto empty ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Auto fill ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Interior light ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Child lock ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Convenient mode to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Edge lighting ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Edge lighting colour to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Edge lighting brightness to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Fan speed to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Fan speed to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Ice maker ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Storage mode to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Light brightness to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn the light ...
Fails the Flow if the appliance refuses the change, rather than reporting success it did not achieve.
Samsung Appliance
Turn Avoid direct wind ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Mute beep once ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Pet filter ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Rapid freezing ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Rapid cooling ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Sabbath mode ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Sanitize ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Smart sensing cooling ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Target humidity to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn UV sterilisation ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Water tank light ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Welcome lighting ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Set Airflow direction to ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Samsung Appliance
Turn Wrinkle prevention ...
Fails the Flow if the appliance refuses the change, rather than reporting a success it did not achieve.
Support
Har du problem med den här appen? Kontakta utvecklaren här.
Vad är nytt?
Version 1.2.0 — Three new Flow triggers for air conditioners: when the mode changes, when the fan speed changes, and when the wind direction changes. Each carries the new value, so you can compare it or log it, and each pairs with the matching "… is" condition if you only care about one setting — When mode changed, and mode is Cool. These were asked for so a Flow could notice somebody using the remote and hold an automation off for a while. Worth knowing before you build that: the trigger cannot tell who made the change, so your own Flow setting the mode looks exactly like the remote. To react only to someone else, compare the value against what your Flow last set. The card says so too. Registrations for live updates are now spaced further apart. A report with hardware measurements showed the previous rate was faster than some appliances tolerate, and that being too quick can leave a unit unresponsive until it is reconnected. Also picks up a transport fix for live updates of large resources arriving truncated or out of order. Washers, dryers, dishwashers and AirDressers now report how many more washes there are before the appliance recommends a drum clean.
SmartThings Local
SmartThings Local är inte kompatibelt med vald Homey.
SmartThings Local installeras på Homey inom kort.
Ändringslogg
Vi kommer att skicka en tacksamhet till Geunwon Mo!
Vi låter Geunwon Mo veta att du älskar appen.
Ditt förslag har skickats
Vi skickar ett meddelande till Geunwon Mo om att du har skickat ett förslag.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
