PELS Strømstyring
Hard cap breach imminent — no managed devices left to limit
PELS Strømstyring
Hold effekttoppene nede og styr elbillading, varme og varmtvann etter strømprisen.
PELS reduserer effekttoppene ved å senke ladestrømmen, justere varmen eller pause enheter med lavere prioritet. Ladestrømmen økes og enhetene starter igjen når det er ledig effekt. Appen styrer blant annet Easee- og Zaptec-ladere, varmtvannsberedere, panelovner, varmepumper og hjemmebatterier gjennom styringsfunksjonene enhetenes Homey-apper tilbyr. Du velger hvilke enheter som skal få strøm først, også når utstyret kommer fra ulike produsenter.
Med Capacity limit setter du en grense for gjennomsnittlig effekt per time eller kvarter for å holde nettleien nede. Grid import limit gjelder effekten du henter fra nettet her og nå. Grensene kan brukes hver for seg eller sammen. Målingene kommer fra Homey Energy, en HAN-leser eller en Flow. Hytta eller sokkelleiligheten kan ha egen måler og effektgrense. Effektstyringen er like nyttig med fast strømpris.
Med Smart tasks kan bilen være ladet til 80 % innen klokka 07, stua varm ved hjemkomst eller varmtvannsberederen ha fått en bestemt energimengde. PELS velger de billigste timene fram til fristen. Når batterinivået er tilgjengelig i Homey, bruker PELS det i ladeplanen. Temperaturstyringen tar også hensyn til kvarterpriser.
PELS beregner norsk spotpris med nettleie og strømstøtte, eller bruker priser fra Homey Energy, Power by the Hour eller Flows. Tidsavhengige priser og nettleie som er lagt inn i den valgte priskilden, tas med i planleggingen. I et Enova-støttet anlegg kan PELS stå for pris- og effektstyringen.
Soloverskudd kan brukes til varmtvann, oppvarming og elbillading. PELS tilpasser ladestrømmen til produksjonen. Et hjemmebatteri som Sessy eller Marstek Venus kan lagre overskuddet som de andre enhetene ikke bruker. PELS reduserer batteriladingen når enheter med høyere prioritet trenger effekt, og bruker batteriet til å holde forbruket under effektgrensen.
Home, Away og Night har egne temperaturer og prioriteringer. Flows kan bytte modus når du drar hjemmefra eller legger deg.
Det veiledede oppsettet ligger under Homey > Mer > Apper > PELS > Innstillinger. Simulation mode viser hvordan PELS ville styrt enhetene før du slår på automatisk styring.
Støttede enheter
Flow-kort
Klikk på en enhet ovenfor for å kun vise relaterte Flow-kort.
Når …
Fires when PELS expects one part of your home to exceed its hard cap in the selected capacity period, with every managed device there already turned off or at its lowest step. The [[home]] tag names that part: the Main home, or a meter area by name. Use it to alert someone to go and turn something off by hand. Daily budget overruns do not fire this trigger.
PELS Strømstyring
Hard cap breach imminent for at least Must last at least (seconds) seconds — no managed devices left to limit
Fires once when PELS has expected one part of your home to exceed its hard cap in the selected capacity period, without a break, for the time you choose, with every managed device there already turned off or at its lowest step. If the situation clears inside that time, nothing fires. PELS limits managed devices immediately either way — this only decides when your Flow starts. Use it instead of Hard cap breach imminent — manual action needed when a brief spike is not worth a notification. The [[home]] tag names the part of the home: the Main home, or a meter area by name. Daily budget overruns do not fire this trigger.
PELS Strømstyring
Daily budget adjusted for the weather forecast
Fires once a day when PELS sets your daily budget from the weather forecast. Requires the weather insight's automatic apply to be turned on. Manual and Flow budget changes do not fire it.
PELS Strømstyring
Smart task ended for Device
Fires once when a smart task ends. The [[outcome]] tag tells you how it ended — succeeded (target reached and held), missed (ready-by time passed before reaching the target), or abandoned (cleared by hand or the device dropped out). Values are stable lowercase ids — filter on them downstream. The [[shortfall_known]] flag is false when the device-side delta was not observable and [[shortfall]] fell back to 0; gate any numeric comparison on it.
PELS Strømstyring
Smart task schedule changed for Device
Fires when the smart task is rescheduled with a different number of hours — for example when new prices arrive, or when the device runs faster than estimated. Hour swaps that keep the same total and kWh-only redistributions stay quiet.
PELS Strømstyring
Smart task status changed for Device
Fires when PELS saves a new smart task status for the chosen device. Short mid-hour recalculations do not fire it. Filter on the [[status]] tag downstream; values are stable lowercase ids: waiting / on_track / at_risk / unachievable / satisfied.
PELS Strømstyring
PELS wants Device at a different step
Fires when PELS decides a stepped device should move to a different configured step. Use it in flows that translate PELS intent into a vendor-specific action.
PELS Strømstyring
No car matched to EV charger after Wait (minutes) minutes
Fires once when a connected charger has waited this long without a car match. Start with 1 minute for a confirmation notification. Automatic matching continues. A match or unplug ends the wait.
PELS Strømstyring
Operating mode changed to Operating mode
Use this to trigger flows when PELS switches to a different operating mode.
PELS Strømstyring
Price level changed to Price level
PELS Strømstyring
PELS price list was updated
PELS Strømstyring
Current price is one of Lowest count lowest in the Hours hours before End hour:00
PELS Strømstyring
Current price is one of Lowest count lowest prices today
PELS Strømstyring
Device smart task has Hours remaining (or fewer) hours or fewer remaining
Fires once when the hours remaining until the smart task's Ready by drops to the chosen value or fewer. Re-arms when the Ready by is rescheduled. Use it to act a fixed lead-time before a deadline (e.g. 2 hours or fewer). The [[hours_remaining]] tag carries the whole hours remaining at the crossing.
Og …
PELS Strømstyring
Device smart task is Status
True when the saved smart task status for this device matches the chosen status.
PELS Strømstyring
EV charger is waiting to match a car
True while the charger is connected, has cars selected in PELS settings, and has no usable car association.
PELS Strømstyring
Device has a smart task
True when this device has a smart task stored in PELS.
PELS Strømstyring
Is there enough available power for Required power (kW) kW?
Use this to check if the current available power is enough to add the requested load.
PELS Strømstyring
Does Device have available power for Required power (kW) kW?
True when the house has room for this device to draw the requested kW. PELS waits about 60 seconds after limiting the device, and asks for extra room when recent attempts to bring it back already fell short — so flows do not flap the device on and off.
PELS Strømstyring
Operating mode is Mode
Use this to create flows that only run when PELS is in a specific mode (e.g., Home, Away, Night).
PELS Strømstyring
Device has budget exemption
Use this to check if the selected device is ignored by daily budget control while still counting in real usage.
PELS Strømstyring
Is power-limit control enabled for Device?
Use this to check whether PELS may limit or resume the selected device: to stay under your grid import limit or hard cap, to keep to your daily budget, or to follow your solar surplus.
PELS Strømstyring
Is Device managed by PELS?
Use this to check if PELS is currently managing the selected device.
PELS Strømstyring
Price level changes to Price level within Hours h
True when a coming price period switches to the chosen level within this many hours. If the price is already at that level, it has to leave it and come back to count. The first period after missing prices counts as a change too. Uses the prices PELS has now, so the answer can change when tomorrow's prices arrive or a new day starts. If PELS has no price for the current period, the Flow fails instead of answering.
PELS Strømstyring
Price level is Price level
PELS Strømstyring
Current price is one of Lowest count lowest in the Hours hours before End hour:00
PELS Strømstyring
Current price is one of Lowest count lowest prices today
Så …
PELS Strømstyring
Add budget exemption for Device
Exclude this device from daily budget control. Real usage still counts in charts and budget reporting.
PELS Strømstyring
Allow Device's smart task to Permission When
Choose what PELS may do to keep this smart task's deadline, and when: go over today's budget, limit lower-priority devices, or reserve power so this task can start sooner — which keeps enough power available for it to begin, and never switches anything off. 'While it's scheduled to run' applies it the whole time the task is active; the change takes effect on the next plan refresh and sticks until you change it or clear the smart task.
PELS Strømstyring
Clear smart task for Device
Removes the active smart task for this device.
PELS Strømstyring
Associate Car with EV charger for this connection
Confirms the selected car for the charger’s current connection, using its battery reading even if the car app has not reported it plugged in. Select the charger first. The car must already be selected for this charger in PELS settings. A delayed Flow response applies to the connection active when this action runs.
PELS Strømstyring
Disable power-limit control for Device
Keep PELS from limiting or resuming this device while power-limit control is disabled.
PELS Strømstyring
Enable power-limit control for Device
Allow PELS to limit or resume this device: to stay under your grid import limit or hard cap, to keep to your daily budget, or to follow your solar surplus.
PELS Strømstyring
Remove budget exemption for Device
Make this device follow daily budget control again.
PELS Strømstyring
Report battery level for Charger device as Battery level (%) %
Store battery percentage for a managed charger without requiring the charger itself to expose a battery capability.
PELS Strømstyring
Report power Power (W) W
Send the current whole-house power reading (W) from your meter so PELS can track energy use for the selected capacity period and stay under the hard cap. If your meter reports a signed value, send it as-is: a negative reading means you are exporting to the grid.
PELS Strømstyring
Report stepped load for Device as Step
Use this after a vendor-specific action card, or when the device changes step outside PELS, so PELS knows which configured step is currently selected.
PELS Strømstyring
Report stepped load for Device matching Power
Use this when a device app gives you a power value instead of a step name. PELS matches the configured step by planning power. Accepts values like 1750 or 1750 W.
PELS Strømstyring
Set capacity limit to Limit (kW) kW
Changes the hard cap, for example by time of day. It does not turn on Capacity limit.
PELS Strømstyring
Set operating mode to Mode (e.g. home, away, vacation)
Use this to automatically switch PELS modes based on time, presence, or other triggers in your flows.
PELS Strømstyring
Set daily budget to Budget (kWh) kWh
Use this to adjust your daily energy budget from flows. Set to 0 to disable the daily budget.
PELS Strømstyring
Set the temperature for Device in Mode to Target temperature (°C) °C
Saves the device's target temperature for a mode, the same setting as the device's Temperature per mode section. Choose Active mode to change whichever mode is in force when the Flow runs. With "Return to mode target" selected for the device, PELS applies it with price and solar adjustments and power limiting on top. With "Save as current mode target", PELS applies it without price or solar adjustments; power limiting still applies. With "Keep the new temperature", PELS saves it but does not apply it.
PELS Strømstyring
Set the Adjustment for Device to Amount (°C) °C
Saves how far PELS moves this device's temperature in cheap or expensive hours, the same setting as the device's Price response section. Use 0 to stop that adjustment. Needs Price-based control turned on for the device. Applied only while "Respond to prices" is on under Price-aware devices, and not while the device is set to "Keep the new temperature" or "Save as current mode target".
PELS Strømstyring
Set what happens when the temperature of Device changes outside PELS: Choice
The same setting as "When the temperature changes outside PELS" in the device's Setup section. With "Keep the new temperature", PELS stops setting this device's temperature: mode targets and price and solar adjustments stop, and PELS cannot limit its power by lowering the temperature. With "Save as current mode target", price and solar adjustments stop and power limiting continues. While the device has an active Smart task, only "Return to mode target" is accepted. Switching back to "Return to mode target" lets PELS set the temperature again: the mode target, with price and solar adjustments and power limiting on top.
PELS Strømstyring
Deliver Energy (kWh) kWh to Device by Ready by
PELS runs the device in the cheapest hours before the ready-by time, within the hard cap and, unless you allow more, the daily budget, until it has taken this much energy, counted from its power readings. For on/off devices like a water heater on a relay, or EV chargers, including chargers with current control. The device needs a live power reading. For EV chargers, you can choose an energy target with or without a linked car or battery reading; the energy includes charging losses. A water heater that is already hot or a car that stops accepting charge can leave the task short of its energy target. The task auto-disables once the deadline passes; run this card from a recurring Flow (for example every evening at 22:00) to set it up for the next night.
PELS Strømstyring
Charge EV charger to Target battery (%) % by Ready by
PELS plans charging from the device settings, prices, budget, and the hard cap. The smart task auto-disables once the deadline passes; run this card from a recurring Flow (e.g. when the EV is plugged in) to re-arm it for the next session.
PELS Strømstyring
Set EV charger charging phase to Phase
Use this after the charger or car is already using this phase. PELS uses it to calculate charging power; it does not switch the charger hardware.
PELS Strømstyring
Set external prices for today from Price data (JSON)
Paste the price JSON from Power by the Hour's "price changed" card tag. Single quotes are accepted (e.g., {'0':0.2747,'1':0.2678,...}).
PELS Strømstyring
Set external prices for tomorrow from Price data (JSON)
Paste the price JSON from Power by the Hour's "price changed" card tag. Single quotes are accepted (e.g., {'0':0.2747,'1':0.2678,'2':0.261,...}).
PELS Strømstyring
Heat Device to Target temperature (°C) °C by Ready by
PELS plans heating from the device settings, prices, budget, and the hard cap. The smart task auto-disables once the deadline passes; run this card from a recurring Flow (e.g. on a daily schedule) to re-arm it for the next run.
Kontrollprogrammer
Støtte
Har du et problem med denne appen? Kontakt utvikleren ved å sende en e-post.
Nyheter
Versjon 3.20.0 — When a charger is plugged in but PELS has no battery level for the car, New smart task, the device page and the Create smart task widget now offer a task for an amount of energy instead, with 10 to 40 kWh as one-tap choices in the widget. The task plans from the charger's own power, so it no longer waits all night for a car app that never reports the level. Outside Norway, PELS now takes prices from Power by the Hour when that app can price your home and you have not chosen a price source, so the markups you set there apply. Once devices follow prices, PELS no longer switches source by itself, and Electricity prices offers Use Power by the Hour instead. Setup outside Norway is clearer. The price suggestion says PELS already has your prices and goes straight to choosing devices. In Sweden, the Limits step asks whether your grid company charges for peak use. Limits & safety shows the hard cap PELS uses until you set one, with a button to keep it.
PELS Strømstyring
Denne appen kan styre alle aspekter ved Homey.
PELS Strømstyring er ikke kompatibel med den valgte Homey.
PELS Strømstyring vil straks installeres på Homey.
Endringslogg
Vi sender en takk til Ole Markus With!
Vi lar Ole Markus With vite at du elsker appen. Vurder å støtte Ole Markus With ved å gi en donasjon?
Doner til Ole Markus With
Utvikleren av PELS Strømstyring tar imot donasjoner.
Gjør en donasjon for å si takk!
Forslaget ditt er sendt
Vi vil varsle Ole Markus With om at du har sendt et forslag.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
