Luxtronik Heat Pump
희망 온도가 변경되면
Luxtronik Heat Pump Manager
Comfort and hot water, perfectly tuned.
Luxtronik Heat Pump Manager brings your Luxtronik-based heat pump into Homey — with full sensor visibility, smart flow integration, and direct control over heating and hot water. Whether you want to automate hot water heating with solar surplus, adjust operating modes, or get notified when your heat pump changes state, this app gives you the tools to do it.
Compatible with Alpha-Innotec, CTA, Novelan, Roth, Elco, Buderus, Nibe, Wolf Heiztechnik and many other Luxtronik-based systems. The app uses the standardised Luxtronik interface and works across different system configurations and firmware versions.
지원되는 디바이스
Flow 카드
위의 디바이스를 클릭하면 관련 Flow 카드만 표시됩니다.
언제...
Luxtronik Heat Pump
온도가 변경되면
Luxtronik Heat Pump
알람이 켜지면
Luxtronik Heat Pump
알람이 꺼지면
Luxtronik Heat Pump
Cooling mode changed
Luxtronik Heat Pump
Hot Water Boost (Party) started
Luxtronik Heat Pump
Hot Water Boost (Auxiliary) started
Luxtronik Heat Pump
Heating mode changed
Luxtronik Heat Pump
Hot water mode changed
Luxtronik Heat Pump
Heat pump state changed
Luxtronik Heat Pump
Error occurred
Luxtronik Heat Pump
Hot Water Boost (Auxiliary Heating) ended
Luxtronik Heat Pump
Hot Water Boost (Party) ended
Luxtronik Heat Pump
Device became unavailable
Luxtronik Heat Pump
Device became available again
Luxtronik Heat Pump
Thermal Disinfection ended
Luxtronik Heat Pump
Error cleared
Luxtronik Heat Pump
Outdoor temperature dropped below Temperature (°C) °C
Luxtronik Heat Pump
Outdoor temperature rose above Temperature (°C) °C
Luxtronik Heat Pump
Room temperature dropped below Temperature (°C) °C
Luxtronik Heat Pump
Room temperature rose above Temperature (°C) °C
그리고...
Luxtronik Heat Pump
알람이 켜지면
Luxtronik Heat Pump
The cooling mode is Mode
Luxtronik Heat Pump
The heating mode is Mode
Luxtronik Heat Pump
The hot water mode is Mode
Luxtronik Heat Pump
The heat pump state is State
Luxtronik Heat Pump
Thermal disinfection is active
Luxtronik Heat Pump
Hot water boost (auxiliary heating) is active
Luxtronik Heat Pump
Hot water boost (party) is active
Luxtronik Heat Pump
Device is available
Luxtronik Heat Pump
Heating status is Status
Luxtronik Heat Pump
Hot water status is Status
Luxtronik Heat Pump
Outdoor temperature is above Temperature (°C) °C
Luxtronik Heat Pump
Outdoor temperature is below Temperature (°C) °C
Luxtronik Heat Pump
Room temperature is above Temperature (°C) °C
Luxtronik Heat Pump
Room temperature is below Temperature (°C) °C
그러면...
Luxtronik Heat Pump
희망 온도 설정 °C
Luxtronik Heat Pump
Restore hot water hysteresis to configured value
Luxtronik Heat Pump
Set cooling mode to Mode
Luxtronik Heat Pump
Minimize hot water hysteresis (set to 0.5 K)
Luxtronik Heat Pump
Set heating mode to Mode
Luxtronik Heat Pump
Set hot water mode to Mode
Luxtronik Heat Pump
Set heating temperature correction to Correction °C (−5 to +5) °C
Shifts the heating curve up or down. Positive values increase the flow temperature (warmer), negative values decrease it (cooler). Does not change the heating mode.
Luxtronik Heat Pump
Set hot water target temperature to Temperature °C (30 to 65) °C
Luxtronik Heat Pump
Start Hot Water Boost (Auxiliary Heating) for Duration (minutes) minutes
Luxtronik Heat Pump
Stop Hot Water Boost (Auxiliary Heating)
Luxtronik Heat Pump
Start Hot Water Boost (Party) for Duration (minutes) minutes
Luxtronik Heat Pump
Stop Hot Water Boost (Party)
Luxtronik Heat Pump
Set max. outdoor temperature to Temperature °C (10 to 45) °C
Luxtronik Heat Pump
Set heating limit to Temperature °C (5 to 30) °C
Luxtronik Heat Pump
Set return temperature hysteresis to Hysteresis K (0.5 to 10) K
Controls how far the return temperature may drop below the setpoint before the heat pump restarts. A smaller value means tighter control but more frequent compressor cycles.
Luxtronik Heat Pump
Set hot water hysteresis to Hysteresis K (0.5 to 10) K
Controls how far the hot water temperature may drop below the setpoint before the heat pump starts reheating. A smaller value keeps the water closer to the target but increases compressor cycles.
Luxtronik Heat Pump
Enable thermal disinfection
Activates continuous thermal disinfection (legionella protection). The heat pump heats the hot water tank to the disinfection setpoint (default 65 °C) and automatically deactivates once the target is reached.
Luxtronik Heat Pump
Disable thermal disinfection
Deactivates continuous thermal disinfection mode.
지원
이 앱에 문제가 있습니까? 개발자에게 문의하려면 여기를 클릭하세요..
새로운 기능
버전 2.1.9 — Adding a heat pump no longer requires looking up its IP address. The pairing screen has a Search network button that finds controllers on your network and fills in their address and port; typing it in by hand still works for anything the search misses. Results that answered the Luxtronik discovery packet are labelled accordingly, so you can tell them apart from devices merely found by manufacturer address. More importantly, the app now keeps track of the address: when your router hands the heat pump a new one, the setting follows and the connection is re-established instead of the device going offline. A DHCP reservation is therefore no longer necessary. Heat pumps added before this update start tracking their address the first time they are seen at their configured one.
Luxtronik Heat Pump Manager
선택하신 Homey에 Luxtronik Heat Pump Manager이(가) 호환되지 않습니다.
Luxtronik Heat Pump Manager이(가) 곧 Homey에 설치됩니다.
업데이트 로그
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
