ESP Easy
The distance value has changed
ESP Easy
Build your own sensors
Questa app non è compatibile con Homey Pro (Early 2023).
ESP Easy is a firmware for ESP32 boards like the WeMos D1 and NodeMCU. It allows you to quickly make custom devices with switches, sensors and other hardware to build your own domotica appliances. With this app, you can connect them to Homey!
With the ESP Easy app, you can add every 'device' separately on Homey. For example; you have one ESP board in the bedroom with both a temperature and a air quality sensor attached? You can add three devices to Homey: the board itself and two environment sensor! Furthermore; all GPIO pins are available for both input and output and the app also allows you to send custom commands to the ESP Easy board.
Met de ESP Easy app kun je elke 'device' appart toevoegen als apparaat in Homey. Heb je bijvoorbeeld een bordje in de meterkast welke met de P1 poort van je watermeter is verbonden maar ook een temperatuursensor heeft? Dan kun je in Homey drie apparaten toevoegen: het ESP bordje zelf, een P1 meter en een temperatuursensor.
As my own use cases are limited, I need your input for Supporting more boards and devices. Please help me on Github or on the forum by sending information about your setup or contributing code.
Dispositivi supportati
Schede dei Flow
Clicca su un dispositivo qui sopra per visualizzare solo le schede dei Flow correlate.
Quando...
ESP Easy
The distance value has changed
ESP Easy
The distance value has changed
ESP Easy
The dust value has changed
ESP Easy
Equivalent CO2 changed
ESP Easy
Available heap blocks changed
ESP Easy
Idle time changed
ESP Easy
System load changed
ESP Easy
The full spectrum luminance changed
ESP Easy
The infrared luminance changed
ESP Easy
The visible spectrum luminance changed
ESP Easy
Il valore di PM1 è cambiato
ESP Easy
Il valore di PM10 è cambiato
ESP Easy
The power factor value has changed
ESP Easy
System RAM usage changed
ESP Easy
Raw value changed
ESP Easy
Raw sensor value changed
ESP Easy
Signal strength changed
ESP Easy
TVOC changed
ESP Easy
'Unknown value' changed
ESP Easy
Uptime changed
ESP Easy Unit
L'intensità del segnale è cambiata
ESP Easy Unit
Unit rebooted
Triggers when reported uptime is lower then last reported uptime. (Doesn't detect a reboot that occurs within one minute of last boot.)
ESP Easy Unit
Unit WiFi reconnected
P1 Energy Meter
L'energia è cambiata
Switch Input
The switch is pressed long
Trigger conditions depend on the device configuration in the ESP unit.
Switch Input
The switch is double-clicked
Trigger conditions depend on the device configuration in the ESP unit.
Poi...
ESP Easy Unit
Send command ESP Easy command, will be send through HTTP
ESP Easy Unit
Start event Event name
ESP Easy Unit
Start event Event name Event parameter
ESP Easy Unit
Set task Value name or ID to New value
ESP Easy Unit
Run (update) task Task name or ID
GPIO Melody Output
Play personalized melody RTTTL Melody like: d=8,o=6,b=340:c,e,g
GPIO Pulse Output
Send pulse of length Duration in milliseconds
GPIO Tone Output
Play tone of Frequency in hertzHz for Duration in millisecondsms
Supporto
Hai un problema con questa app? Contatta lo sviluppatore qui.
Novità
Versione 1.12.1 — Support for changes in firmware 7.4, the app will now cap sensorvalues to the min/max of a capabilty and some other bugfixes.
ESP Easy
ESP Easy non è compatibile con l'Homey selezionato.
ESP Easyverrà installato a breve su Homey.
Changelog
Inviaremos un ringraziamento a Joolee !
Faremo sapere a Joolee che ami l'applicazione. Forse potresti considerare di supportare Joolee facendo una donazione?
Dona a Joolee
Lo sviluppatore di ESP Easy accetta donazioni.
Fai una donazione per ringraziarlo!
