Peblar Charger
The power changed
Peblar EV Charger
Plug in. Power up. Automate.
Warning! This app might not work properly.
This app version is currently being tested, and has not yet been reviewed. It might not work as expected.
Be extra careful when installing this app.
Control and monitor your Peblar EV Charger from Homey. Start or pause charging, tune charging limits and phase mode, use smart charging modes, and automate charger status, alarms, and management features in Flow.
Supported devices
Flow cards
Click on a device above to show related Flow cards only.
When...
Peblar Charger
Started charging
Peblar Charger
Stopped charging
Peblar Charger
The EV charger charging state changed ...
Peblar Charger
The generic alarm turned on
Peblar Charger
The generic alarm turned off
Peblar Charger
Cable plugged in
Peblar Charger
Cable unplugged
Peblar Charger
Charger authentication fails
Peblar Charger
Charger goes offline
Peblar Charger
Charger comes online
Peblar Charger
Charging authorized with an RFID tag
Triggers when the charger reports a new active session authorized with a registered RFID tag. Existing sessions on startup and card enrollment do not trigger this Flow. Requires the Web UI password and session history support. Short sessions between polls may be missed.
Peblar Charger
Charging started
Peblar Charger
Charging stopped
Peblar Charger
An error code is received
Peblar Charger
Faults are cleared
Peblar Charger
Smart charging mode changed
Peblar Charger
Warnings are cleared
Peblar Charger
A warning code is received
And...
Peblar Charger
Is charging
Peblar Charger
The EV charger charging state is ...
Peblar Charger
The generic alarm is on
Peblar Charger
Alarm details contain Search text
Checks the readable Peblar alarm text for a code or phrase
Peblar Charger
The cable is connected
True when the charger reports a connected cable or vehicle
Peblar Charger
The charge current is greater than Amperes A
True when the charger setpoint is above the given value
Peblar Charger
The charge current is less than Amperes A
True when the charger setpoint is below the given value
Peblar Charger
The charger authentication failed
True when the local Peblar API rejects the configured API token
Peblar Charger
The charger is online
True when the local Peblar API is currently reachable
Peblar Charger
Charging state is ...
Checks the current charging session state reported by the charger
Peblar Charger
A charger fault is active
True when Peblar reports one or more active error codes
Peblar Charger
A firmware update is available
True when Peblar reports a newer firmware or customization package
Peblar Charger
Force 1 phase is Enabled
Checks whether Force1Phase is enabled on the charger
Peblar Charger
Has active error ...
True when the charger currently has the given error code
Peblar Charger
Peblar charging state is Peblar charging state
Checks the raw CP state reported by the Peblar API
Peblar Charger
Phase mode is Phase mode
Checks whether the Peblar charger is currently in 1F or 3F mode
Peblar Charger
RFID tag RFID UID is registered
Checks whether an RFID UID exists in the Peblar standalone authorization list. Requires the Peblar web password.
Peblar Charger
Smart charging mode is ...
Checks if the current smart charging mode equals the value
Peblar Charger
A charger warning is active
True when Peblar reports one or more active warning codes
Then...
Peblar Charger
Start charging
Peblar Charger
Stop charging
Peblar Charger
Add RFID tag RFID UID as Description
Registers an RFID tag in the Peblar standalone authorization list. Requires the Peblar web password. Not available when the charger is managed by a back office (OCPP).
Peblar Charger
Configure Custom Solar: always charge Always charge, target Power target (W) W, threshold Power threshold (W) W
Updates the charger’s Custom Solar settings without changing its charging mode. Requires compatible firmware (1.10+), solar support and the Web UI password. Power values are signed whole watts; negative thresholds are supported.
Peblar Charger
Present RFID tag Registered RFID tag remotely
Toggles session authorization: authorizes an unauthorized session or stops an authorized session. Requires a registered card, Web UI password and REST API write access. Acceptance precedes the state change; check the charger state. Not available when the charger is managed by a back office (OCPP).
Peblar Charger
Reboot charger
Requests a Peblar hard reboot through the hidden web-password API
Peblar Charger
Remove RFID tag Registered RFID tag
Select a registered card to delete. Requires the Peblar Web UI password.
Peblar Charger
Remove RFID tag RFID UID
Removes an RFID tag from the Peblar standalone authorization list. Requires the Peblar web password.
Peblar Charger
Set buzzer volume to Volume
Sets the Peblar buzzer volume through the hidden web-password API
Peblar Charger
Set charging current: Amperes A
Sets the maximum charging current setpoint
Peblar Charger
Set charge limit to Charge limit (A) A with Phase mode
Sets the official Peblar charge limit and phase mode in one write
Peblar Charger
Set Force 1 phase to Enabled
Sets the Peblar Force1Phase toggle without changing the current limit
Peblar Charger
Set LED brightness to automatic
Sets the LED brightness automatically using the built-in ambient light sensor
Note: this requires the Web UI password to be entered in the settings
Peblar Charger
Set LED brightness to Brightness%
Sets the Peblar LED brightness to your desired value
Note: this requires the Web UI password to be entered in the settings
Peblar Charger
Set LED off
Turns off the charger's LED
Note: this requires the Web UI password to be entered in the settings
Peblar Charger
Set phase mode to Phase mode
Switches the charger between 1F and 3F while preserving the current limit
Peblar Charger
Set smart charging mode: ...
Sets the Peblar smart charging mode via the hidden API
Peblar Charger
Start charging at Charge limit (A) A with Phase mode
Starts charging with one explicit official Peblar write
Widgets
Support
Having an issue with this app? Contact the developer via the developer website.
What’s new
Version 4.5.0 — Adds a compact charging mode widget for Homey Dashboard (with optional power bar and pause/resume buttons) and a session energy capability. RFID features are now disabled when the charger is managed by a back office over OCPP.
Peblar EV Charger
Peblar EV Charger is not compatible with the selected Homey.
Peblar EV Charger will install on Homey shortly.
Changelog
We’ll send a thank you to Kyle Michiels!
We’ll let Kyle Michiels know you love the app.
Your suggestion has been sent
We’ll notify Kyle Michiels you’ve sent a suggestion.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
