Elegoo Centauri Carbon
Temperaturen ændrede sig
Elegoo 3D Printers
Integrating Elegoo 3D Printers effortlessly into your smart home via the local SDCP protocol.
Advarsel! Denne app fungerer muligvis ikke ordentligt.
Denne app er ved at blive testet og er aldrig blevet anmeldt. Den fungerer muligvis ikke som forventet.
Vær ekstra forsigtig, når du installerer denne app.
Control and monitor your Elegoo 3D printer directly from Homey using the local SDCP v3 protocol. No cloud account required. Everything runs on your local network.
FEATURES
Real-time monitoring of your printer. Print progress, current layer and estimated time remaining. Live camera snapshot updated every 5 seconds. Full fan control including part cooling, auxiliary and exhaust fans. Chamber light toggle. Emergency stop, pause and resume print controls. Print speed and extrusion factor adjustment.
SENSORS AND INSIGHTS
Nozzle temperature
Bed temperature
Chamber temperature
Print progress
Layer progress
Current layer and total layers
Z position
Remaining print time
Current filename
Printer status
Fan speeds
USB disk status
Camera enabled status
Active video streams
Motor status
Network interface
Remaining storage
Firmware version
Printer model and IP address
SETUP
Add the app and use the built-in discovery to find your printer automatically on the local network. The printer must be connected to the same Wi-Fi or LAN as your Homey.
NOTE
Temperature values and sensor data are only available when the printer is active. The printer does not broadcast sensor readings while idle.
Understøttede enheder
Flow-kort
Klik på en enhed ovenfor for kun at vise relaterede Flow-kort.
Når...
Elegoo Centauri Carbon
Kontaktalarmen blev aktiveret
Elegoo Centauri Carbon
Kontaktalarmen blev deaktiveret
Elegoo Centauri Carbon
Bed temperature reached target
Elegoo Centauri Carbon
Camera becomes ...
Elegoo Centauri Carbon
Chamber temperature reaches Temperature°C
Elegoo Centauri Carbon
Door is [[state]]
Elegoo Centauri Carbon
Error Detected
Elegoo Centauri Carbon
Filament Runout
Elegoo Centauri Carbon
Firmware update available
Elegoo Centauri Carbon
Print reaches layer Layer number
Elegoo Centauri Carbon
Motors become ...
Elegoo Centauri Carbon
Nozzle temperature reached target
Elegoo Centauri Carbon
Print Cancelled
Elegoo Centauri Carbon
Print Finished
Elegoo Centauri Carbon
Print Paused
Elegoo Centauri Carbon
Print Resumed
Elegoo Centauri Carbon
Print Started
Elegoo Centauri Carbon
Printer Offline
Elegoo Centauri Carbon
Printer Online
Elegoo Centauri Carbon
Print progress reaches Percentage%
Elegoo Centauri Carbon
Printer status changed
Elegoo Centauri Carbon
USB drive is [[state]]
Elegoo Centauri Carbon
Someone started viewing camera stream
Elegoo Centauri Carbon
Viewers stopped watching camera
Og...
Elegoo Centauri Carbon
Kontaktalarmen er tændt
Elegoo Centauri Carbon
Chamber Light is On
Elegoo Centauri Carbon
Is Offline
Elegoo Centauri Carbon
Is Paused
Elegoo Centauri Carbon
Is Printing
Så...
Elegoo Centauri Carbon
Emergency Stop
Elegoo Centauri Carbon
Home ...
Elegoo Centauri Carbon
Pause Print
Elegoo Centauri Carbon
Resume Print
Elegoo Centauri Carbon
Send G-code e.g. M104 S200 or G28
Sends a custom G-code or Klipper command directly to the printer.
Elegoo Centauri Carbon
Turn chamber light ...
Elegoo Centauri Carbon
Set ... speed to 100%
Elegoo Centauri Carbon
Set speed preset to ...
Elegoo Centauri Carbon
Skip preheating
Skips the current preheating phase and starts the print immediately.
Elegoo Centauri Carbon
Stop material feeding
Stops active filament extrusion or material feeding.
Support
Har du et problem med denne app? Kontakt udvikleren her.
Hvad er nyt
Version 1.2.6 — Fix critical memory leaks causing spawn ENOMEM errors: throttled Insights database logging, removed unneeded camera polling, optimized IPC capability updates, and hardened WebSocket reconnection.
Elegoo 3D Printers
Elegoo 3D Printers er ikke kompatibel med den valgte Homey.
Elegoo 3D Printers bliver snart installeret på Homey.
Ændringslog
Vi sender en tak til Thomas Veivåg!
Vi lader Thomas Veivåg vide, at du elsker appen. Overvej måske at støtte Thomas Veivåg ved at give en donation?
Donér til Thomas Veivåg
Udvikleren af Elegoo 3D Printers tager imod donationer.
Giv et bidrag for at sige tak!
Dit forslag er blevet sendt
Vi giver Thomas Veivåg besked, når du har sendt et forslag.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
