Elegoo 3D Printers

Integrating Elegoo 3D Printers effortlessly into your smart home via the local SDCP protocol.

Control and monitor your Elegoo 3D printer directly from Homey using the local SDCP v3 protocol. No cloud account required. Everything runs on your local network. FEATURES Real-time monitoring of your printer. Print progress, current layer and estimated time remaining. Live camera snapshot updated every 5 seconds. Full fan control including part cooling, auxiliary and exhaust fans. Chamber light toggle. Emergency stop, pause and resume print controls. Print speed and extrusion factor adjustment. SENSORS AND INSIGHTS Nozzle temperature Bed temperature Chamber temperature Print progress Layer progress Current layer and total layers Z position Remaining print time Current filename Printer status Fan speeds USB disk status Camera enabled status Active video streams Motor status Network interface Remaining storage Firmware version Printer model and IP address SETUP Add the app and use the built-in discovery to find your printer automatically on the local network. The printer must be connected to the same Wi-Fi or LAN as your Homey. NOTE Temperature values and sensor data are only available when the printer is active. The printer does not broadcast sensor readings while idle.

Læs mere ›

Understøttede enheder

Flow-kort

Klik på en enhed ovenfor for kun at vise relaterede Flow-kort.

Når...

Elegoo Centauri Carbon

Temperaturen ændrede sig

Elegoo Centauri Carbon

Kontaktalarmen blev aktiveret

Elegoo Centauri Carbon

Kontaktalarmen blev deaktiveret

Elegoo Centauri Carbon

Bed temperature reached target

Elegoo Centauri Carbon

Camera becomes ...

Elegoo Centauri Carbon

Chamber temperature reaches Temperature°C

Elegoo Centauri Carbon

Door is ...

Elegoo Centauri Carbon

Error Detected

Elegoo Centauri Carbon

Filament Runout

Elegoo Centauri Carbon

Firmware update available

Elegoo Centauri Carbon

Print reaches layer Layer number

Elegoo Centauri Carbon

Motors become ...

Elegoo Centauri Carbon

Nozzle temperature reached target

Elegoo Centauri Carbon

Print Cancelled

Elegoo Centauri Carbon

Print Finished

Elegoo Centauri Carbon

Print Paused

Elegoo Centauri Carbon

Print Resumed

Elegoo Centauri Carbon

Print Started

Elegoo Centauri Carbon

Printer Offline

Elegoo Centauri Carbon

Printer Online

Elegoo Centauri Carbon

Print progress reaches Percentage%

Elegoo Centauri Carbon

Printer status changed

Elegoo Centauri Carbon

USB drive is ...

Elegoo Centauri Carbon

Someone started viewing camera stream

Elegoo Centauri Carbon

Viewers stopped watching camera

Og...

Elegoo Centauri Carbon

Kontaktalarmen er tændt

Elegoo Centauri Carbon

Chamber Light is On

Elegoo Centauri Carbon

Is Offline

Elegoo Centauri Carbon

Is Paused

Elegoo Centauri Carbon

Is Printing

Så...

Elegoo Centauri Carbon

Emergency Stop

Elegoo Centauri Carbon

Home ...

Elegoo Centauri Carbon

Pause Print

Elegoo Centauri Carbon

Resume Print

Elegoo Centauri Carbon

Send G-code e.g. M104 S200 or G28

Elegoo Centauri Carbon

Turn chamber light ...

Elegoo Centauri Carbon

Set ... speed to 100%

Elegoo Centauri Carbon

Set speed preset to ...

Elegoo Centauri Carbon

Skip preheating

Elegoo Centauri Carbon

Stop material feeding

Support

Har du et problem med denne app? Kontakt udvikleren her.

Hvad er nyt

Version 1.2.7 — Resolved camera stream memory churn, optimized threshold trigger IPC queries, fixed zombie connection heartbeat watchdog, and added state dropdowns to door and USB flow triggers.

Se ændringslog

Fungerer på

Opdateret for 1 uge siden

Version 1.2.7

Udvikler Thomas Veivåg

Kategori Hårde hvidevarer

Kræver Homey v5.0.0 eller nyere

Support Kontakt »

Problemer Rapporter et problem »

Kildekode Se kilde »

Bidrag Doner »

Installer