OpenQuatt Controller
La potencia ha cambiado
OpenQuatt
Your heat pump, live and local — no cloud required
OpenQuatt connects Homey Pro directly to the OpenQuatt heat pump controller on your own network. The controller is discovered automatically and all data arrives in real time over a live local connection — no polling and no cloud account needed. Monitor supply, outside and room temperatures, power consumption, the active control mode and the aux relay, and switch manual cooling or the relay straight from Homey.
Automate everything with an extensive set of Flow cards for heating, cooling, faults, defrosting, the boiler and silent mode, and feed the dew point from your own room sensors so the controller can cool safely without condensation. A dashboard widget shows live temperatures, power, efficiency and status at a glance. Requires a Quatt heat pump running the OpenQuatt firmware and a Homey Pro (Early 2023 or newer). This app is a community project and is not affiliated with Quatt B.V.
Dispositivos compatibles
Tarjetas Flow
Haz clic en el dispositivo de arriba para mostrar solo las tarjetas Flow relacionadas.
Cuando...
OpenQuatt Controller
The control mode changed
OpenQuatt Controller
Cooling started
OpenQuatt Controller
Cooling stopped
OpenQuatt Controller
Heating started
OpenQuatt Controller
Heating stopped
OpenQuatt Controller
A fault was detected
OpenQuatt Controller
The fault was resolved
OpenQuatt Controller
Defrosting started
OpenQuatt Controller
Defrosting stopped
OpenQuatt Controller
The boiler turned on
OpenQuatt Controller
The boiler turned off
OpenQuatt Controller
Silent mode turned on
OpenQuatt Controller
Silent mode turned off
OpenQuatt Controller
The dew point became available
OpenQuatt Controller
The dew point was lost
Without a valid dew point the controller blocks or limits cooling, depending on its configuration.
Y...
OpenQuatt Controller
Is cooling
OpenQuatt Controller
Is heating
OpenQuatt Controller
A fault is active
OpenQuatt Controller
Is defrosting
OpenQuatt Controller
The boiler is active
OpenQuatt Controller
Silent mode is active
OpenQuatt Controller
A dew point is available
OpenQuatt Controller
Cooling is permitted
OpenQuatt Controller
The aux relay (R2) function is ...
Entonces...
OpenQuatt Controller
Set silent mode override to ...
OpenQuatt Controller
Force control mode ...
A forced mode blocks normal heating and cooling until you switch back to Automatic.
OpenQuatt Controller
Set boiler assist ...
Turning this off also disables the boiler fallback on heat-pump faults.
OpenQuatt Controller
Set OpenQuatt control ...
Off disables the entire OpenQuatt control loop.
OpenQuatt Controller
Set manual cooling enable ...
OpenQuatt's manual cooling override, which forces cooling permission regardless of the selected source. To feed the regular permission signal from Homey, use “Set cooling permission” instead.
OpenQuatt Controller
Set the aux relay (R2) function to ...
Chooses what the R2 relay follows. Pick External control to switch it yourself with the Switch the aux relay (R2) card.
OpenQuatt Controller
Send dew point Dew point (°C) °C to the controller
Sent straight to the controller (firmware with API input support; MQTT as fallback via the device settings). The last value is re-sent every minute until it expires.
OpenQuatt Controller
Update the dew point for Living room from temperature Temperature (°C) °C and humidity Humidity (%) %
Calculates the room's dew point from temperature and relative humidity; the highest recently updated room is sent straight to the controller (firmware with API input support; MQTT as fallback via the device settings).
Advanced
OpenQuatt Controller
Send outside temperature Outside temperature (°C) °C to the controller
Sent straight to the controller (firmware with API input support; MQTT as fallback via the device settings). The last value is re-sent every minute until it expires. Pick the source in the OpenQuatt web app under Settings → Sources / integrations → Sensor selection.
OpenQuatt Controller
Send room temperature Room temperature (°C) °C to the controller
Sent straight to the controller (firmware with API input support; MQTT as fallback via the device settings). The last value is re-sent every minute until it expires. Pick the source in the OpenQuatt web app under Settings → Sources / integrations → Sensor selection.
OpenQuatt Controller
Send room setpoint Setpoint (°C) °C to the controller
Sent straight to the controller (firmware with API input support; MQTT as fallback via the device settings). The controller keeps this value until you send a new one; the app re-sends it every minute and after a restart. Pick the source in the OpenQuatt web app under Settings → Sources / integrations → Sensor selection.
OpenQuatt Controller
Set heating permission ...
Tells the controller whether heating is allowed at all. Sent straight to the controller (firmware with API input support; MQTT as fallback via the device settings). The controller keeps this value until you send a new one; the app re-sends it every minute and after a restart. Pick the source in the OpenQuatt web app under Settings → Sources / integrations → Sensor selection.
OpenQuatt Controller
Set cooling permission ...
Tells the controller whether cooling is allowed at all. Sent straight to the controller (firmware with API input support; MQTT as fallback via the device settings). The controller keeps this value until you send a new one; the app re-sends it every minute and after a restart. Pick the source in the OpenQuatt web app under Settings → Sources / integrations → Sensor selection. This is the regular permission signal, not the manual cooling override.
OpenQuatt Controller
Switch the aux relay (R2) ...
Switches the R2 contact itself. Only works while the aux relay function is set to External control.
Widgets
Asistencia
¿Tienes algún problema con esta aplicación? Contacta con el desarrollador aquí.
Novedades
Versión 1.4.1 — Fixes empty values on recent controller firmware. The live update stream renamed its entities, so every reading in Homey stayed blank while the flow cards kept working. The app now understands both the old and the new naming.
OpenQuatt
OpenQuatt no es compatible con el Homey seleccionado.
OpenQuatt se instalará en Homey en breve.
Registro de cambios
¡Enviaremos un agradecimiento a OpenQuatt!
Le haremos saber a OpenQuatt que te encanta la aplicación.
Se han enviado tus sugerencias
Avisaremos a OpenQuatt para que esté al tanto de las sugerencias.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
