intelligent-heat-pump
The target temperature changed
Adlar Castra Heatpump
Local access to the Aurora series heatpump device.
Warning! This app might not work properly.
This app version is currently being tested, and has not yet been reviewed. It might not work as expected.
Be extra careful when installing this app.
Local access to the Aurora series heat pump device.
Setup:
To find out the local key to use, refer to the GitHub source: /docs/Get Local Keys - instruction.pdf
Usage:
See the file: /docs/Flow Card handling/flow-cards-overview.md for instructions on how to use the flow cards in your Advanced Flow.
For an overview of the Capabilities, see: /docs/Heatpump specs/capabilities-overview.md
For information about the mapping between Capabilities and Flow Cards, see: /docs/Flow Card handling/capability-flowcard-mapping.md
Supported devices
Flow cards
Click on a device above to show related Flow cards only.
When...
intelligent-heat-pump
Turned on
intelligent-heat-pump
Turned off
intelligent-heat-pump
The waterflow changed
intelligent-heat-pump
The power changed
intelligent-heat-pump
Ambient temperature Condition Temperature (°C)°C
Triggers when ambient temperature goes above or below a specified level - useful for weather compensation
intelligent-heat-pump
Backwater turned State
Triggers when backwater system changes state
intelligent-heat-pump
Coiler temperature Condition Temperature (°C)°C
Triggers when electricity coiler temperature goes above or below a specified level
intelligent-heat-pump
Compressor frequency Condition Frequency (Hz) Hz
Triggers when compressor frequency goes above or below a specified level
intelligent-heat-pump
Compressor turned State
Triggers when compressor changes state
intelligent-heat-pump
Countdown timer finished
Triggers when the system countdown timer reaches zero
intelligent-heat-pump
Daily consumption reached Daily threshold (kWh) kWh
Triggers when daily electricity consumption reaches specified threshold
intelligent-heat-pump
Defrost turned State
Triggers when defrost system changes state
intelligent-heat-pump
Discharge temperature Condition Temperature (°C)°C
Triggers when discharge temperature goes above or below a specified level
intelligent-heat-pump
Economizer inlet temperature Condition Temperature (°C)°C
Triggers when economizer inlet temperature goes above or below a specified level
intelligent-heat-pump
Economizer outlet temperature Condition Temperature (°C)°C
Triggers when economizer outlet temperature goes above or below a specified level
intelligent-heat-pump
EEV pulse-steps Condition Pulse-steps
Triggers when Electronic Expansion Valve (EEV) pulse-steps go above or below a specified level
intelligent-heat-pump
Current load Condition Current (A) amperes
Triggers when electrical current goes above or below a specified level
intelligent-heat-pump
EVI Open pulse-steps Condition Pulse-steps
Triggers when Enhanced Vapor Injection (EVI) pulse-steps go above or below a specified level
intelligent-heat-pump
Fan motor frequency Condition Frequency (Hz) Hz
Triggers when fan motor frequency goes above or below a specified level
intelligent-heat-pump
Fault code Fault code detected
Triggers when a system fault is detected
intelligent-heat-pump
High pressure temperature Condition Temperature (°C)°C
Triggers when high pressure saturation temperature goes above or below a specified level
intelligent-heat-pump
Incoiler temperature Condition Temperature (°C)°C
Triggers when incoiler temperature goes above or below a specified level
intelligent-heat-pump
Inlet temperature Condition Temperature (°C)°C
Triggers when water inlet temperature goes above or below a specified level
intelligent-heat-pump
Low pressure temperature Condition Temperature (°C)°C
Triggers when low pressure saturation temperature goes above or below a specified level
intelligent-heat-pump
Outlet temperature Condition Temperature (°C)°C
Triggers when water outlet temperature goes above or below a specified level
intelligent-heat-pump
Phase A voltage Condition Voltage (V) volts
Triggers when Phase A voltage goes above or below a specified level
intelligent-heat-pump
Phase B current Condition Current (A) amperes
Triggers when Phase B current goes above or below a specified level
intelligent-heat-pump
Phase B voltage Condition Voltage (V) volts
Triggers when Phase B voltage goes above or below a specified level
intelligent-heat-pump
Phase C current Condition Current (A) amperes
Triggers when Phase C current goes above or below a specified level
intelligent-heat-pump
Phase C voltage Condition Voltage (V) volts
Triggers when Phase C voltage goes above or below a specified level
intelligent-heat-pump
Power consumption exceeded Power threshold (W) W
Triggers when power consumption exceeds specified threshold (requires power monitoring support)
intelligent-heat-pump
Suction temperature Condition Temperature (°C)°C
Triggers when suction temperature goes above or below a specified level
intelligent-heat-pump
Tank temperature Condition Temperature (°C)°C
Triggers when water tank temperature goes above or below a specified level
intelligent-heat-pump
Total consumption reached Consumption milestone (kWh) kWh
Triggers when total electricity consumption reaches specified milestones
intelligent-heat-pump
Water flow rate Condition Flow rate (L/min) L/min
Triggers when water flow rate goes above or below a specified level
And...
intelligent-heat-pump
Is turned on
intelligent-heat-pump
Hot water curve setting is Hot water curve setting
Check if the hot water curve setting matches the selected setting
intelligent-heat-pump
Compressor is running
Check if the compressor is currently running
intelligent-heat-pump
Device power is Power state
Check if the device power state matches the selected state
intelligent-heat-pump
3-phase electrical balance is within Balance tolerance (%)% tolerance
Check if the 3-phase electrical currents are balanced within specified tolerance
intelligent-heat-pump
Fault is active
Check if a fault is currently active (fault code > 0)
intelligent-heat-pump
Heating curve setting is Heating curve
Check if the heating curve setting matches the selected curve
intelligent-heat-pump
Heating mode is Heating mode
Check if the heating mode matches the selected mode
intelligent-heat-pump
Hot water temperature is Comparison Hot water temperature (°C)°C
Check if the hot water temperature matches the specified condition
intelligent-heat-pump
Power consumption is above Power threshold (W) watts
Check if current power consumption is above or below a threshold (requires power monitoring support)
intelligent-heat-pump
System pulse-steps differential is above Pulse-steps differential
Check if the pulse-steps difference between EEV and EVI is above or below a threshold
intelligent-heat-pump
Target temperature is Comparison Temperature (°C)°C
Check if the target temperature matches the specified condition
intelligent-heat-pump
Ambient temperature is above Temperature°C
Check if the ambient temperature is above or below a specific value
intelligent-heat-pump
Temperature differential is above Temperature differential (°C)°C
Check if the temperature difference between inlet and outlet is above or below a threshold
intelligent-heat-pump
Total consumption is above Consumption threshold (kWh) kWh
Check if total electricity consumption is above or below a threshold
intelligent-heat-pump
Electricity consumption checking is Comparison Electricity consumption checking
Check if the electricity consumption checking level matches the specified condition
intelligent-heat-pump
Water flow rate is above Flow rate (L/min) L/min
Check if water flow rate is above or below specified threshold
intelligent-heat-pump
Water control mode is Comparison Water control mode
Check if the water control mode matches the specified condition
intelligent-heat-pump
Work mode is Work mode
Check if the work mode matches the selected mode
Then...
intelligent-heat-pump
Set the temperature °C
intelligent-heat-pump
Turn on
intelligent-heat-pump
Turn off
intelligent-heat-pump
Toggle on or off
intelligent-heat-pump
Set hot water curve setting to Hot water curve setting
Set the hot water curve setting for optimal efficiency
intelligent-heat-pump
Set device power to Power state
Set the device power state
intelligent-heat-pump
Set heating curve setting to Heating curve setting
Set the heating curve setting
intelligent-heat-pump
Set heating mode to Heating mode
Set the heating operation mode
intelligent-heat-pump
Set hot water temperature to Hot water temperature (°C)
Set the hot water temperature setting
intelligent-heat-pump
Set target temperature to Temperature (°C)
Set the target temperature for the heat pump
intelligent-heat-pump
Set electricity consumption checking to Electricity consumption checking
Set the electricity consumption checking level
intelligent-heat-pump
Set water control mode to Water control mode
Set the water control mode setting
intelligent-heat-pump
Set work mode to Work mode
Set the system work mode
Support
Having an issue with this app? Contact the developer by sending an e-mail.
What’s new
Version 0.93.0 — Added option to enable/disable slider control capabilities for cleaner interface.
Adlar Castra Heatpump
Adlar Castra Heatpump is not compatible with the selected Homey.
Adlar Castra Heatpump will install on Homey shortly.
Changelog
We’ll send a thank you to H Hi!
We’ll let H Hi know you love the app.
Your suggestion has been sent
We’ll notify H Hi you’ve sent a suggestion.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
