Nibe heatpumps

Control your heatpump with Homey

Warnung! Diese App funktioniert möglicherweise nicht richtig.

Diese App wird getestet und wurde noch nie überprüft. Sie funktioniert möglicherweise
nicht wie erwartet. Sei besonders vorsichtig, wenn du diese App installierst.

« Zurück zur normalen Version

Control your heatpump with Homey

Mehr lesen ›

Unterstützte Geräte

Flow-Karten

Klicke oben auf ein Gerät, um nur verwandte Flow-Karten anzuzeigen.

Wenn ...

F1145
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F1155
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F1245
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F1255
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F1345
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F1355
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F370
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F470
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F730
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
F750
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
Nibe heatpumps
Compressor status changed
S1155
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
S1156
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
S1255
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
S1256
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
S735
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
SMO 20
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
SMO 40
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
SMO S40
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM 225
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM 310
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM 320
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM 325
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM 500
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM S320
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM S325
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.
VVM S500
Heat pump status changed
i
Runs when the heat pump switches between e.g. heating, hot water and off.

Und ...

F1145
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F1145
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F1145
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F1145
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F1145
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F1145
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F1145
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F1145
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F1145
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F1155
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F1155
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F1155
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F1155
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F1155
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F1155
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F1155
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F1155
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F1155
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F1245
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F1245
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F1245
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F1245
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F1245
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F1245
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F1245
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F1245
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F1245
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F1255
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F1255
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F1255
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F1255
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F1255
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F1255
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F1255
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F1255
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F1255
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F1345
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F1345
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F1345
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F1345
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F1345
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F1345
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F1345
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F1345
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F1345
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F1355
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F1355
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F1355
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F1355
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F1355
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F1355
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F1355
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F1355
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F1355
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F370
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F370
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F370
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F370
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F370
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F370
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F370
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F370
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F370
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F370
Ventilation boost is active
i
Checks if ventilation boost mode is active
F470
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F470
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F470
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F470
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F470
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F470
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F470
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F470
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F470
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F470
Ventilation boost is active
i
Checks if ventilation boost mode is active
F730
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F730
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F730
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F730
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F730
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F730
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F730
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F730
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F730
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F730
Ventilation boost is active
i
Checks if ventilation boost mode is active
F750
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
F750
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
F750
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
F750
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
F750
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
F750
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
F750
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
F750
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
F750
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
F750
Ventilation boost is active
i
Checks if ventilation boost mode is active
S1155
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
S1155
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
S1155
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
S1155
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
S1155
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
S1155
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
S1156
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
S1156
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
S1156
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
S1156
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
S1156
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
S1156
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
S1255
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
S1255
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
S1255
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
S1255
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
S1255
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
S1255
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
S1256
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
S1256
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
S1256
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
S1256
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
S1256
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
S1256
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
S735
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
S735
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
S735
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
S735
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
S735
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
S735
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
SMO 20
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
SMO 20
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
SMO 20
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
SMO 20
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
SMO 20
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
SMO 20
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
SMO 20
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
SMO 20
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
SMO 20
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
SMO 40
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
SMO 40
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
SMO 40
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
SMO 40
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
SMO 40
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
SMO 40
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
SMO 40
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
SMO 40
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
SMO 40
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
SMO S40
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
SMO S40
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
SMO S40
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
SMO S40
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
SMO S40
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
SMO S40
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM 225
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM 225
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
VVM 225
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM 225
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
VVM 225
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM 225
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM 225
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
VVM 225
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM 225
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM 310
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM 310
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
VVM 310
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM 310
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
VVM 310
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM 310
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM 310
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
VVM 310
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM 310
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM 320
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM 320
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
VVM 320
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM 320
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
VVM 320
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM 320
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM 320
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
VVM 320
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM 320
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM 325
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM 325
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
VVM 325
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM 325
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
VVM 325
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM 325
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM 325
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
VVM 325
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM 325
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM 500
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM 500
Heating curve is Comparison Value
i
Checks if the heating curve value matches the condition
VVM 500
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM 500
Heating factor system is Comparison Value
i
Checks if the heating factor system value matches the condition
VVM 500
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM 500
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM 500
Temporary luxury is active
i
Checks if temporary luxury hot water mode is active
VVM 500
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM 500
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM S320
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM S320
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM S320
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM S320
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM S320
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM S320
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM S325
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM S325
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM S325
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM S325
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM S325
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM S325
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range
VVM S500
Degree minutes is Comparison Value DM
i
Checks if the degree minutes value matches the condition
VVM S500
Heating curve offset is Comparison Value
i
Checks if the heating curve offset value matches the condition
VVM S500
Indoor temperature is Comparison Temperature °C
i
Checks if the current indoor temperature matches the condition
VVM S500
Outside temperature is Comparison Temperature °C
i
Checks if the current outside temperature matches the condition
VVM S500
Difference between indoor and outdoor temperature is Comparison Temperature difference °C
i
Checks if the difference between indoor and outdoor temperature matches the condition
VVM S500
Temperature type temperature is between Minimum and Maximum °C
i
Checks if the temperature is within the specified range

Dann ...

F1145
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F1145
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F1145
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F1145
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F1145
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F1145
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F1145
Set temperature to Temperature °C
F1155
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F1155
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F1155
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F1155
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F1155
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F1155
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F1155
Set temperature to Temperature °C
F1245
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F1245
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F1245
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F1245
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F1245
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F1245
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F1245
Set temperature to Temperature °C
F1255
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F1255
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F1255
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F1255
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F1255
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F1255
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F1255
Set temperature to Temperature °C
F1345
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F1345
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F1345
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F1345
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F1345
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F1345
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F1345
Set temperature to Temperature °C
F1355
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F1355
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F1355
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F1355
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F1355
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F1355
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F1355
Set temperature to Temperature °C
F370
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F370
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F370
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F370
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F370
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F370
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F370
Set temperature to Temperature °C
F370
Turn ventilation boost State
i
Activates or deactivates ventilation boost mode
F470
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F470
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F470
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F470
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F470
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F470
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F470
Set temperature to Temperature °C
F470
Turn ventilation boost State
i
Activates or deactivates ventilation boost mode
F730
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F730
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F730
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F730
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F730
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F730
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F730
Set temperature to Temperature °C
F730
Turn ventilation boost State
i
Activates or deactivates ventilation boost mode
F750
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
F750
Set heating curve to Value
i
Sets the heating curve value on the heat pump
F750
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
F750
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
F750
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
F750
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
F750
Set temperature to Temperature °C
F750
Turn ventilation boost State
i
Activates or deactivates ventilation boost mode
S1155
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
S1155
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
S1155
Set temperature to Temperature °C
S1156
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
S1156
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
S1156
Set temperature to Temperature °C
S1255
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
S1255
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
S1255
Set temperature to Temperature °C
S1256
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
S1256
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
S1256
Set temperature to Temperature °C
S735
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
S735
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
S735
Set temperature to Temperature °C
SMO 20
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
SMO 20
Set heating curve to Value
i
Sets the heating curve value on the heat pump
SMO 20
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
SMO 20
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
SMO 20
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
SMO 20
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
SMO 20
Set temperature to Temperature °C
SMO 40
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
SMO 40
Set heating curve to Value
i
Sets the heating curve value on the heat pump
SMO 40
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
SMO 40
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
SMO 40
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
SMO 40
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
SMO 40
Set temperature to Temperature °C
SMO S40
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
SMO S40
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
SMO S40
Set temperature to Temperature °C
VVM 225
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM 225
Set heating curve to Value
i
Sets the heating curve value on the heat pump
VVM 225
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM 225
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
VVM 225
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
VVM 225
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
VVM 225
Set temperature to Temperature °C
VVM 310
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM 310
Set heating curve to Value
i
Sets the heating curve value on the heat pump
VVM 310
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM 310
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
VVM 310
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
VVM 310
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
VVM 310
Set temperature to Temperature °C
VVM 320
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM 320
Set heating curve to Value
i
Sets the heating curve value on the heat pump
VVM 320
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM 320
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
VVM 320
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
VVM 320
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
VVM 320
Set temperature to Temperature °C
VVM 325
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM 325
Set heating curve to Value
i
Sets the heating curve value on the heat pump
VVM 325
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM 325
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
VVM 325
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
VVM 325
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
VVM 325
Set temperature to Temperature °C
VVM 500
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM 500
Set heating curve to Value
i
Sets the heating curve value on the heat pump
VVM 500
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM 500
Set the room sensor value of the heat factor system to Value
i
Setting the room sensor value of the heat factor system on the heat pump
VVM 500
Set max electrical addition to Power
i
Sets the maximum electrical addition power. Options are fetched from your pump.
VVM 500
Turn temporary luxury State
i
Activates or deactivates temporary luxury hot water mode
VVM 500
Set temperature to Temperature °C
VVM S320
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM S320
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM S320
Set temperature to Temperature °C
VVM S325
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM S325
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM S325
Set temperature to Temperature °C
VVM S500
Set degree minutes to Value DM
i
Sets the degree minutes value on the heat pump
VVM S500
Set heating curve offset to Value
i
Sets the heating curve offset value on the heat pump
VVM S500
Set temperature to Temperature °C

Support

Der Entwickler dieser App bietet keinen direkten Support an.

Was ist neu?

Version 2.0.0 — Big update! Every NIBE model now has its own driver (F-series, S-series and SMO/VVM controllers) with parameters made for that model. Existing devices keep working, but add your heat pump again to get the new features. New: Fireplace mode for S-series with ventilation, e.g. S735: turns the ventilation down for a while when you light the wood stove, then restores it (enable under Advanced settings). Fixed: target temperature on F730/F750 no longer changes the minimum supply temperature. Improved power and energy estimation. New Flow trigger for heat pump status, and Flow cards for more models.

Changelog ansehen

Nibe heatpumps

Nibe heatpumps ist mit dem gewählten Homey nicht kompatibel.

Nibe heatpumps wird in Kürze auf Homey installiert.
Installieren