Actuator / Dimmer
Turned on
Eaton xComfort
Lighting, climate and comfort — locally in sync.
Bring your local Eaton xComfort Bridge into Homey for everyday control of lighting, appliances and loads, shading, heating, safety sensors, weather readings, and energy insight from one or more bridges. The app keeps communication local to the bridge, helps avoid duplicate devices during setup, and exposes useful xComfort status in Homey without needing the Eaton mobile app for daily use.
Use Homey to automate xComfort scenes and their bridge automation, room lighting and shading, astro-based scene or room actions, climate presets, water protection, energy-aware loads, dimmer behavior, safe actuator unlocking, and optional bridge remote-access control while keeping auth-key or user/password bridge credentials in App Settings. The xComfort Rooms dashboard widget controls each bridge room by its stable ID, regardless of custom or localized names. Local bridge discovery can fill changed network addresses safely after authenticated identity verification, and Bridge Status includes detailed Bridge 4.x client and firmware health. A redacted diagnostics export is available from settings when support information is needed.
Read-only access to Homey's location is used only for the astro Flow condition. Coordinates stay on Homey and are not included in diagnostics exports.
Supported devices
Flow cards
Click on a device above to show related Flow cards only.
When...
Actuator / Dimmer
Turned off
Actuator / Dimmer
The dim level changed
Actuator / Dimmer
Actuator started blinking
Uses reported blinking mode, not individual flashes. Initial and reconnect reports do not trigger this card.
Actuator / Dimmer
Actuator stopped blinking
Uses reported blinking mode, not individual flashes. Initial and reconnect reports do not trigger this card.
Actuator / Dimmer
Actuator locked
Actuator / Dimmer
Actuator unlocked
Actuator / Dimmer
Actuator fault detected or changed
Actuator / Dimmer
Actuator fault cleared
Binary Input
The generic alarm turned on
Binary Input
The generic alarm turned off
Door / Window Sensor
The contact alarm turned on
Door / Window Sensor
The contact alarm turned off
Eaton xComfort
Client bridge state changed
Eaton xComfort
Bridge connected
Triggers when a bridge connection is (re)established.
Eaton xComfort
Bridge disconnected
Triggers when a bridge connection is lost.
Eaton xComfort
Bridge Energy Control mode changed
Eaton xComfort
Bridge energy priority changed
Eaton xComfort
Bridge reported a health issue
Eaton xComfort
Bridge health issue cleared
Eaton xComfort
Bridge remote-access permission changed
Eaton xComfort
Bridge remote-service state changed
Eaton xComfort
Smart-scene condition state changed
Eaton xComfort
Electricity spot tariff rating changed
Motion Sensor
The motion alarm turned on
Motion Sensor
The motion alarm turned off
Room Lights
Turned on
Room Lights
Turned off
Room Status
Turned on
Room Status
Turned off
Room Status
The temperature changes
Room Status
The humidity changed
Room Status
The power changed
Room Status
The power meter changed
Shading / Blinds
The state changed ...
Shading / Blinds
The position changed
Shading / Blinds
The generic alarm turned on
Shading / Blinds
The generic alarm turned off
Shading / Blinds
Shading fault detected or changed
Shading / Blinds
Shading fault cleared
Shading / Blinds
Shading safety protection activated
Shading / Blinds
Shading safety protection cleared
Thermostat / Heating
The temperature changes
Thermostat / Heating
The target temperature changed
Thermostat / Heating
The thermostat mode changed to ...
Thermostat / Heating
Thermostat right button pressed
Thermostat / Heating
Thermostat left button pressed
Thermostat / Heating
Heating preset changed
Thermostat / Heating
Aggregate heating request changed
Wall Switch
Wall switch pressed
Wall Switch
Wall switch pressed up
Wall Switch
Wall switch pressed down
Wall Switch
Wall switch double pressed up
Inferred from two same-direction Bridge events within 1 second. Single-press Flows also run. Some devices may report holds as repeated events.
Wall Switch
Wall switch double pressed down
Inferred from two same-direction Bridge events within 1 second. Single-press Flows also run. Some devices may report holds as repeated events.
Water Sensor
The water alarm turned on
Water Sensor
The water alarm turned off
Water Sensor
Assigned Water Guard sensor issue detected
Only for Water Guard devices, not ordinary leak sensors.
Water Sensor
Assigned Water Guard sensor issue cleared
Only for Water Guard devices, not ordinary leak sensors.
Weather Station
The temperature changes
Weather Station
The luminance changed
Weather Station
The rain alarm turned on
Weather Station
The rain alarm turned off
Weather Station
Wind speed changed
Weather Station
Left brightness changed
Weather Station
Middle brightness changed
Weather Station
Right brightness changed
And...
Actuator / Dimmer
Is turned on
Actuator / Dimmer
Actuator is blinking
Uses reported blinking mode, not individual flashes. Unknown or disconnected state reports an error.
Actuator / Dimmer
Actuator is locked
Actuator / Dimmer
Actuator is not blinking
Uses reported blinking mode, not individual flashes. Unknown or disconnected state reports an error.
Actuator / Dimmer
Actuator is unlocked
Actuator / Dimmer
Actuator reports ...
Uses the last reported fault. Unknown state or disconnection does not clear it.
Actuator / Dimmer
Device has a fault
Actuator / Dimmer
Physical load is energized
Accounts for inverted relay outputs (invOut) reported by the xComfort Bridge.
Binary Input
The generic alarm is on
Door / Window Sensor
The contact alarm is on
Eaton xComfort
All known client bridges of Bridge are connected
Eaton xComfort
Energy Control mode of Bridge is ...
Eaton xComfort
Energy priority on Bridge is active
Eaton xComfort
Bridge Bridge is connected
Eaton xComfort
Bridge Bridge is connected without a reported issue
Eaton xComfort
Remote access on Bridge is allowed
Eaton xComfort
Remote service of Bridge is online
Eaton xComfort
Conditions of Smart scene are met
Eaton xComfort
Astro period is ...
Eaton xComfort
Electricity tariff on Bridge is ...
Eaton xComfort
Electricity price on Bridge is below ... /kWh
Motion Sensor
The motion alarm is on
Room Lights
Is turned on
Room Status
Is turned on
Shading / Blinds
The state is ...
Shading / Blinds
The generic alarm is on
Shading / Blinds
Device has a fault
Thermostat / Heating
The thermostat mode is ...
Thermostat / Heating
Heating preset is ...
Thermostat / Heating
Aggregate heating is requested
Water Sensor
The water alarm is on
Water Sensor
Water valve is open
Only for Water Guard devices, not ordinary leak sensors.
Water Sensor
An assigned sensor reports a leak
Only for Water Guard devices, not ordinary leak sensors.
Water Sensor
An assigned sensor has a low battery
Only for Water Guard devices, not ordinary leak sensors.
Water Sensor
An assigned sensor has a bad signal
Only for Water Guard devices, not ordinary leak sensors.
Weather Station
The rain alarm is on
Weather Station
Wind speed is above ... m/s
Weather Station
Left brightness is above ... lx
Weather Station
Middle brightness is above ... lx
Weather Station
Right brightness is above ... lx
Then...
Actuator / Dimmer
Turn on
Actuator / Dimmer
Turn off
Actuator / Dimmer
Toggle on or off
Actuator / Dimmer
Dim to %
Actuator / Dimmer
Set relative dim-level %
Dim or brighten with respect to the device's current dim-level.
Actuator / Dimmer
Reset energy meter of [[device]]
Actuator / Dimmer
Set physical load to ...
Automatically inverts the logical switch command when the actuator uses an inverted relay output (invOut).
Eaton xComfort
Activate scene Scene
Eaton xComfort
Cancel temporary energy priority on Bridge
Eaton xComfort
Set room Room shading to ...
Eaton xComfort
Dim room Room lights to 50 %
Dims all dimmable lights in an xComfort room with a single bridge command. 0% switches the room lights off.
Eaton xComfort
Lock actuator Actuator, dimmer or load
Locks the selected switching or dimming actuator. Ordinary controls may be ignored until it is unlocked. Does not request a new output level.
Eaton xComfort
Refresh energy data from Bridge
Eaton xComfort
Refresh physical state from Bridge
Eaton xComfort
Set Energy Control mode of Bridge to ...
Eaton xComfort
On Bridge, prioritize ... for ... minutes
Eaton xComfort
Set bridge Bridge remote access to ...
Eaton xComfort
Set room Room shading to ... %
0% is fully closed and 100% is fully open.
Eaton xComfort
Set scene Smart scene automation ...
Eaton xComfort
Switch all devices on Bridge ...
Uses Eaton's native whole-home command. This affects every switchable xComfort device, including appliance loads—not only lights.
Eaton xComfort
Switch all lights on Bridge ...
Targets only devices classified as lights, using individual commands. Excludes shades and appliance loads.
Eaton xComfort
Switch room Room lights ...
Eaton xComfort
Unlock actuator Actuator, dimmer or load
Unlocks the selected switching or dimming actuator. Does not request a new on/off state or dim level.
Eaton xComfort
Lock actuator Actuator for ... seconds
Locks the switching or dimming actuator immediately and automatically sends an unlock command when the timer expires.
Room Lights
Turn on
Room Lights
Turn off
Room Lights
Toggle on or off
Room Status
Turn on
Room Status
Turn off
Room Status
Toggle on or off
Room Status
Reset energy meter of [[device]]
Room Status
Switch room lights ...
Shading / Blinds
Set state ...
Shading / Blinds
Set the position to %
Change the position to open (100%), closed (0%), or a value in between.
Shading / Blinds
Step shading ...
Only available for actuators whose xComfort control mode supports timed step/jog commands.
Shading / Blinds
Lock shading actuator
Locks local and automated movement on the xComfort shading actuator in volatile Bridge RAM.
Shading / Blinds
Unlock shading actuator
Shading / Blinds
Acknowledge and clear shading safety state
Thermostat / Heating
Set the temperature °C
Thermostat / Heating
Set the thermostat mode to ...
Thermostat / Heating
Reset energy meter of [[device]]
Thermostat / Heating
Set heating preset to ...
Thermostat / Heating
Set Effect Regulation to ... %
Only for rooms configured for Effect Regulation.
Water Sensor
Set water valve to ...
Only for Water Guard devices, not ordinary leak sensors.
Water Sensor
Mute Water Guard ... alarm
Only for Water Guard devices, not ordinary leak sensors.
Water Sensor
Test the Water Guard alarm
Only for Water Guard devices, not ordinary leak sensors.
Widgets
Support
Having an issue with this app? Contact the developer via the developer website.
What’s new
Version 1.7.78 — Fixes the app still crashing at startup on Homey Pro (Early 2019) and Homey (Early 2019) after 1.7.77. The 32-bit version now also works with the older system software on these models.
Eaton xComfort
Eaton xComfort is not compatible with the selected Homey.
Eaton xComfort will install on Homey shortly.
Changelog
We’ll send a thank you to Mike Taselaar!
We’ll let Mike Taselaar know you love the app.
Your suggestion has been sent
We’ll notify Mike Taselaar you’ve sent a suggestion.
Africa
Asia
Europe
Belgium
Deutsch English
Bulgaria
Croatia
Cyprus
Czech Republic
Estonia
Finland
Greece
Hungary
Iceland
Ireland
Latvia
Lithuania
Malta
Moldova
The Netherlands
Portugal
Romania
Slovakia
Slovenia
Türkiye
Ukraine
United Kingdom
